A-Frame Trailer Jack With 2" Outer Tube Diameter
Do they make the same jack with the outside tube having a diameter of only 2 inches? | I do have an option for you but the Ultimate Trailer Jack part # 322-RDJ-2K only comes with an outer diameter of 2-1/4". The 2" outer diameter tube jacks...
Trailer Jack that Doesnt Hang Down Very Far for a Big Tex Utility Trailer
I have a Big Tex utility trailer that I use often and it has a top wind trailer jack installed. The jack works well however, even when fully raised, it often drags or scrapes the roadway if there is a bump or rise in the road. Is there a jack...
Is There a Folding Trailer Tongue Jack To Replace Jack On a 2021 Karavan 5' X 8' Utility Trailer?
Hi, I have a 2021 Karavan utility trailer 5x8. I am looking for a folding trailer jack that fits in the spot of the current jack. Its an a-frame trailer with the jack in the middle of theA. Thanks | The Ultimate Trailer Jack # 322-RDJ-2K is...
A-Frame Trailer Jack For Older Military Trailer
hi. do you know of any companies that make a 24 vdc trailer tongue jack? I have an old military truck n trailer Id like to set up with one. thanks | There are no 24 volt A-frame trailer jacks, they do require a 12-volt power source. So what...
Recommended Replacement Trailer Jack for a Futura Trailer
I need help finding a jack for my Futura trailer. It has an A frame jack, but the mounting holes are 3.75inch from center to center. Everything that I have been finding is a smaller bolt pattern. | That's definitely an unusual size for the...
Replacement Electric A-Frame Trailer Jack
do you have an electric jack that fits this triangular pattern? It doesntfoot have to be rated very high weight capacity | The triangular pattern you see on the # 322-RDJ-2K and your trailer is pretty standard for A-frame trailers. For an electric...
Recommended Low Profile Manual Trailer Jack For A 3,000 lb Rpod Trailer
I have an RPod180 travel trailer that weighs just a little over 3000 lbs fully loaded. I pull it with a Ford F150 with a Blue Ox WDH. The problem is that I can’t open my tailgate while the trailer is hitched. Do you have a recommendation for...
Recommended A-Frame Tongue Jack for American Hauler Trailer
Hi I’m looking for a new trailer jack for my American hauler The three point bolted on one is bent and doesn’t work now. Which jack would work and is there one that a wheel or like a quick and raise before you have to start cranking it? Thanks...
Recommended Wheel for a Ultimate Trailer Jack
Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2 Lift - 2,000 lbs 322-RDJ-2K Do you have a wheel for the end of the jack? | Yes, we do. It is the Removable 6" Caster for 2-1/4" Trailer Jacks item # JC-102. This has been confirmed to work...
What Top Wind Jack that you Offer has the Shortest Retracted Bracket Height
Im looking for a top wind A frame trailer jack. What is the shortest retracted length is that you have? | The Ultimate Trailer Jack part # 322-RDJ-2K has a retracted height of just 1-3/4" it has by far the shortest retracted length of any of...
How To Stop A-Frame Jack From Scrapping Ground While Going Over Bumps
Hello. I have a 16 foot V nose enclosed motorcycle trailer. It is quite low to the ground and as such the foot of the A-frame tongue jack is only about 5 inches off the ground when hitched to the truck with trailer level. It is constantly dragging...
Is There a Blank Cover Plate Which Can Mount Over Holes For A-Frame Trailer Jack Holes?
I am considering replacing the existing a-frame jack on our utility trailer with the etrailer 2000 lb topwind swivel jack, # TJBB-2001-B. This would provide additional ground clearance for the jack footplate when towing, as well as allowing...
What Does Ultimate Trailer Jack 322-RDJ-2K Weigh
How much does the actual jack weigh. part # 322-RDJ-2K Thx. | Hey Tim, the Ultimate Trailer Jack part # 322-RDJ-2K that you referenced weighs 13 lbs. |
What is Shortest Bracket Height Trailer Jack with Caster Wheel
Hi. I need a trailer jack. Its for a cement mixer. the tongue of the cement mixer is very low to the ground. I have a jack on another nixer and works well. But that tongue is higher up from the ground. I need a trailer jack with a 6” wheel...
Does Ultimate Trailer Jack Fit Standard A-Frame Mounting Bracket
Are most or all the same size and bolt pattern? | Yes, nearly all trailer a-frame bolt patterns for jacks are the exact same so you don't have to measure or verify anything to know that the Ultimate trailer jack # 322-RDJ-2K will fit your trailer. |
Installing 322-RDJ-2K Ultimate Trailer Jack
I just purchased the jack and installed it. Then yeah then I read the instructions and noticed that they state 4 - CRITICAL you/I must Remove plastic retainer and apply either thread lock tape or locking compound to the threads of retainer bolt....
A-Frame Jack For Camper so Tailgate Can Clear Jack
I have a RAM 3500 lb Electric Jack on a Wildwood x-lite 273QBXL trailer we just bought. My truck is a 2018 RAM 2500. The jacks head interferes with the tailgate fully opening. We have 3 dogs that need to ride in the back. Big issue. Is there...
Topwind or Electric Jack to Replace Sidewind Bulldog Jack
Looking to replace my BD1700100301 which I dislike very much with either a top-wind unit that will raise/lower easily or an electric unit. My 24 enclosed trailer stays loaded at about Max 7000lbs. Any help is appreciated. | For a powered a-frame...
Recommended A-Frame Jack with Most Ground Clearance
I would like to know how long the outer tube extends below the A-frame flange. That is the one dimension that is missing in your great video and data sheet. please measure the length from the bottom of the flange to the bottom of the outer...
Will the Ultimate Trailer Jack Work With the Low Profile Replacement Footplate for RAM Jacks
Is the jack foot plate Item # JF-100-ZBK compatible with this jack? Looking for a low profile foot plate. | The Ultimate Trailer Jack part # 322-RDJ-2K should be compatible with the Replacement Footplate part # JF-100-ZBK. This is not something...
Height of Ultimate Trailer Jack # 322-RDJ-2K When Positioned at Lowest Setting
On the Ultimate A-frame trailer jack, can you tell me the measurement from the mounting bracket to the top of the jack when the jack is fully extended down? Also, what is the measurement from the mounting bracket to the bottom of the jack without...
How Far Does Pin of Ultimate Trailer Jack Go into the Jack
How far does the pin go into the jack? I'm worried about it coming out when there's weight on the trailer. | The Ultimate trailer jack, part # 322-RDJ-2K, has a pin used to drop the jack tube. As long as the pin is fully engaged and the safety...
Recommended A-Frame Trailer Jack for Applications with Limited Ground Clearance
What is the shortest bolt-on a-frame jack you have from the bottom of the mounting plate to the bottom of the extendable leg when retracted? My current jack is too long and often hits the ground when towing. Can be light duty, 2000lbs or less....
Do All A-Frame Trailer jacks have the Same Mounting Hole Pattern
Im replacing the a frame Jack on my trailer. Some give the mounting hole distances and some dont. Is there a standard? | Yes, about 99 percent of A-frame jacks use the same mounting pattern. The holes are generally 3 inches apart on center...
Filter Your Search
Contact and Help