!F-150-and-F-250-Light-Duty  x   >   !Windsport Motorhome  x   >   Yates Rubber  x   >  

I currently have a trailer with 32 rollers black yates 343R. looking to exchange with non marking rollers. Which one should I purchase? | For a non-marking wobble roller to replace the ones you have now you'd need to go up to the 5 inch size...

After seeing these rollers, I am concerned that they are not strong enough to support my boat properly, what is their load rating? Our boat is 3800 lbs, the motor is 800, boat is 22 ft. Thanks | I called my contact at Yates Rubber and asked...

Hello! I have a question about: Yates Side Guide Roller for Boat Trailers - Heavy-Duty Rubber - 12 Long - 1/2 Shaft Is the 1/2” hole diameter of the rubber roller an interference fit with the 1/2” diameter steel shaft? I’m trying to find a roller...

My old black rubber aft roller is approx 12 long and has a 5/8 x 13 steel rod with a hat nut on each end. It is different than ones Ive seen, in that it has a thick 3-1/4 dia rubber donut on each end. What do I have here and are they available?...

On the YR500YW-6P wobble roller what is the thickness or width of the center hub that the shaft goes through? I have a roller on my boat trailer that is not available anymore and I am trying to find a replacement that will work. The roller...

What is the difference between the purple and the Tan rollers. I will be installing them on a shore lander trailer. | Both the blue/purple 8 inch keel rollers like part # YR800B and the yellow part # YR800Y are essentially the same thing just...

need two load rite wobble assembly for a 1986 load rite trailer Both are up front, one left, one right. Both are two rollers I wish to replace the entire assembly, not just the roller. Rollers seem to 5 inches in diameter Your form does...

Looking for a Roller Replacement wheel..For my bow roller..size now 3 1/2 inches diameter with 4inch width. inside sleeve 5/8..Any Suggestions? | The # YR450B roller you mentioned comes about as close as we can to the dimensions you mentioned....

Is this product one solid piece or 2 pieces ? | The Yates Side Guide Roller for Boat Trailers # YR9202-4 is one piece. The lines you see are the seam left from the mold that was used to create the roller. |

I need a bow roller assembly that will fit a 3-1/2 wide bracket. Do you have one? | No, we do not have a bow roller assembly that fits a 3-1/2" wide bracket. The closest that we have are for 3" or 4" brackets. 3" - Bow Roller Assembly # YR300Y-325Y 4" -...

I have a 3/4 shaft ,do I need to order a roller with a bigger shaft opening for example a 7/8 shaft hole | We have wobble rollers specifically designed for 3/4 inch shafts like yours. For that we have the part # YR343R-6P which has a center...

I am looking to buy this part and need to know if there are one or two bells per package? Do I need to buy one or two of these to complete the bow roller? Thank you, | The part # YR400Y is sold individually. If you needed two of these to go...

how wide is this wobble roller? | The Yates Heavy-Duty Rubber Ribbed Wobble Roller # YR343R-6P is 3-inches wide and 4-3/8-inches in diameter. The inner hole diameter is slightly under 7/8-inch in order to fit a 3/4-inch diameter roller shaft. |

This 4inch yates roller with 1/2inch shaft appears to have an in the center hole or roller shaft hole for the 1/2inch shaft to slip into. Is that correct for this roller. My existing rollers have a 1/2inch shaft and so I wanted to make sure...

Can I use them on a 2x4 on bunks. | The Yates Keel Pad # YR1203SB is designed to fit on 3" wide frames and crossmembers. To mount them on bunk boards you would have to notch the 2"x4" for them to even fit. Also the pad is not designed to hold...

Hello, Looking for a 7”x5” stopper for tracker trail star boat trailer. The trailer hauls a 24” pontoon boat. I can’t find this specific stopper that is held by two bolts on the trailer’ The picture shows the stopper but it’s not fastened...

Do these Bow Bell come in pairs or individually if I am buying the bow roller | The Yates Bow Bell # YR400BLK that you referenced comes individually in that part number. For a kit that includes the 4 Inch roller, 2 end bells, and corrosion-resistant...

How do you tell if you need 1/2 inch or 5/8 shaft. | Measure the diameter of the hole that's on your current spool roller or measure the diameter of the shaft that your current spool roller rides on and you'll know what size you are in need...

I cant seem to find an appropriate length shaft for this 9 inch roller on your website. They are all either several inches too long or too short. Please send part info for a compatible shaft. | The reason that you are having difficulty finding...

Whats the difference between wobble rollers and rocker rollers? It looks like the # DL21562 and the # YR440R are the same construction, but they have different names. The # DL21564 one looks like different construction also... Please elaborate....

It looks like my current keel rollers have a Z 10 number on them. The one in your picture has a Z 5 number. Otherwise the measurements are the same. My boat is a small cruiser 23 foot bayliner about 4600lbs. I assume these are hard enough to...

I have an 1985 Ez roller boat trailer that needs new wobble roller wheels. I have pictures of the old ones on the trailer. I measured the wheels at the following deminsions: 4 1/2 inches round 3inch thick 1inch center shaft Can you tell me what...

Hello, I am looking at replacing the side guide rollers on my trailer. The current rollers are 12x 2-1/2inch w/ 1/2inch Shaft. I found the correct replacement roller on your site from Yates along with a top cap but I cannot find the right length...

how to remove old retainer ring on wobble rollers | Probably the easiest way to remove a retainer ring, such as # CE10981, to replace a wobble roller is to grip one end with some vise grips and the other end with some pliers. Then twist in opposite...