!Eagle Super Lite Travel Trailer  x   >   !Marquis Motorhome  x   >   AxleTek  x   >   Redline  x   >  

Hello, I am looking to add electric brakes to a utility trailer that does not currently have any or the brake mount flanges. Is it possible to weld the flanges and add the brakes or can I buy an entire axle assembly with the brakes already installed? It...

I want to add electric drum brakes to my homemade boat trailer... I know what I need to do with the electrical, etc... I have a brake controller, etc.. We pulled the bearings out of one wheel and have the numbers... Trailer has dual 3500...

I'm needing new hubs. The old part number is Dexter 8-208, 5 on 4.5 inch standard hub. What would be the new hub part number to replace these? | The Trailer Hub Assembly for 3,500 lb Axles, # 84550BX, was confirmed by Dexter to be the assembly...

Does the kit #AKEBRK-35-SA include the brake drums. They are mentioned as included but not pictured. | What is included are the left and right hand brake assemblies, as well as mounting bolts with the 3,500 lb electric brake kit: - Electric...

I am upgrading from the OE 4 leaf springs to this 5 leaf spring. Which U bolt set will I need for this 5 leaf spring? I have 5200lb. tandem axles. Also, can I use the existing bolt plates on top of the springs? Thank You! | For replacement U-Bolts...

Im looking for a replacement spring like Item # RS16933LH. The part Im trying to replace has a wire diameter of 5/8. What size of wire is Item # RS16933LH? | The Redline Ramp Spring # RS16933LH referenced in your question features an inside...

HI,Are the 10-4 and 10-19 seal interchange? Dimensions are the same. Thank You | The part # 10-40 is a single lip grease seal with a 1.938" inner and 2.510" outer diameter. The part 10-19 # RG06-050 is a double lip grease seal with a 1.719"...

Hello, Looking for a wheel stud from a 12inch x 2inch electric drum brake, 8x6.5inch pattern, 5200 pound axle. 1/2-20 thread, 2.8inch long 2.5inch would work, 0.56inch spline diameter, 0.68inch spline length, stamped U 144inch on head Thanks...

I see that hub # 22834 is no longer available for the older style . Could you tell me the seal number and if you would have 4 ? | Yep, we sure do have the grease seal for your 22834 hub, and what you need is the following: - Grease Seal # 29031 |

When I replace the brakes do I need to replace all bearings and seals? No signs of leaks? I was already given the part numbers for the brakes on my 2018 big Tex 22gn 10k | When you replace your Brakes # 23-450-451 it is a good idea to inspect...

Hi, I have a grand design imagine 2800bh trailer and i am looking for a new/replacement axle with spindles. It appears to be 86.5 hub face to hub face, and 68.5 spring to spring on center If i went to the 3 axle, what else would i need to...

Im setting up all new suspension on a car hauler and would like to use these to achieve a 35inch axle spacing so I can run 235 85 16 tires. I have tandem dexter 6k axles and was planning on using: E94SR 26inch Springs MR27ZR Equalizers MR46ZR...

What is the outside flange dimensions ? | The overall dimensions of the Redline "Junior" Locking Steel Flush Door Latch # L1833 that you referenced can be seen on the photo I have linked for you. I pulled a piece from our warehouse and took...

I have a 1996 procraft 3500 lb trailer What size nut and retainer do I need ? I picked up 3/4 inch and it’s just A bit to small | Although we don't have any way of knowing the spindle nut you need for your trailer, we do have something slightly...

Do you carry calipers and pads for the Al-Ko 10K axles? | Yes we do, for your AL-KO 10k axles the correct caliper for the left hand side of your trailer would be the # BP18-050. For the right hand side the part number is # BP18-060. For replacement...

I got a regular RV ceiling vent to put in the back of our ambulance in Africa. There are times we have over 20 people riding in the back and no air-conditioning. The catch is that i have to take this back to Africa in a trunk and the 14X14in...

I have a old 7500 pound car trailer with 10 inch drums, bolt pattern is 5 on 5.5, Im having a hard time trying to find the right size knurl on the lug with 1/2-20 threads. here are the specs on the lug bolts that i took out: length minus...

If the Brake Mounting Flange for 1-3/4inch Round Trailer Axles - 2K Item # 4-34 is designed for 1-3/4 axles, then why is the center hole 1-5/8 dia. Maybe I received parts from a bad batch? | That is the correct hole size for brake mounting...

Hello, I have a triple 7k axle trailer with electric brakes and I seem to always be replacing a wire do to a short, the spring and star wheel falls out, or a magnet goes haywire. I run a a hot shot and put about 130k miles on a trailer in...

I am looking at the website and I see this in amber and in red, just double checking to see if in fact, red lens is available. Also, can you state the size of the lights, length, height and width? Thanks | The Pacer Performance Hi-Five Truck...

Looking for a quote on lug nut locks for a DARKHORSE Cargo trailer. the size info that I received is ½” X 20 ON 5 X 4.5 PATTERN. | We do have lug nut locks for your 1/2 inch x 20 lug nuts with the Wheel Lock Set for 1/2" Wheel Bolts # RG01-150. This...

I have trailer hubs with 1/2-13 lug bolts. I would like to change them out with studs and lug nuts for ease of maintenance. My current lug bolts are left hand and right hand threads respectively. I think these are the studs I need but im not...

Hello I ordered two of these vents to add ventilation to my 24 ft snowmobile trailer. Where would the best place to put these ? each Side, same side, roof ? I received my vents and I am trying to figure out how to open them ? | The Redline...

Will this pin work as a replacement pin on my blue ox sysytem | Yes, with your Blue Ox system you can use the linch pin you asked about: - Linchpin - 2-1/4" Long x 7/16" Diameter # LP716 |