GMC  x   >   !Peterbilt  x   >   !Austin-Healey  x   >   Yamaha  x   >  

The wiring for the Superwinch comes up about 12 short for the winch connections. What is the best way to extend the wiring leads? They look to be about a 10 or 12ga. Installing on 2005 Yamaha Wolverine 350 FX. Solenoid has been installed in...

So I did all my measurements on my trailer to use these to replace current stock ones. One question I have does it lower or raise the height of the trailer at all? The reason I ask is because my stock measurements are 6 1/4 between mounting...

Can you tell me what outside diameter is of the black cable. I need to buy a rubber grommet to ensure the lack of wearing to cable. | I went to our warehouse to get the Hopkins trailer wire connector # H20046 to provide you the measurement you...

Does this winch mount fit on a 2006 yamaha wolverine 450 4x4 | I spoke with my contact and they said the Bulldog Custom-Fit ATV Winch Mounting Kit, part # BDW15140, will fit the 2006 Yamaha Wolverine 450 4x4. It will also fit the 2006 to 2009...

my 2016 Nissan pathfinder has raised siderails and I want to install factory looking crossbars, what do you recommend. | The Thule Aeroblade Edge Roof Rack part # TH7503-TH7503 that you referenced has been confirmed to fit your 2016 Nissan Pathfinder...

Will this work with the superwinch terra 45? | Yes, the Superwinch Custom-Fit ATV Winch Mounting Kit # SW2202920 will work perfectly with the Superwinch Terra 45. I verified this through Superwinch's fit information. I have attached the written...

I was at the boat launch yesterday, and noticed one tire off the ground. I thought something happened to the equalizer, but after inspection it appears to be fine. There was some wood in the launch ramp I didn’t see because it was dark, and...

Do you make Tonneau covers for a Yamaha Umax? | I have a possible solution for you, however, we do not carry tonneau bed covers for your Yamaha Umax Golfcart / UTV. If you just wanted the cover for looks or to keep the cargo inside the bed,...

Will the Terra 25 and/or 35 fit the above grizzly. I see some people have had trouble because there isnt enough space. If it does fit, what mount is required | For your 2014 Yamaha Grizzly 450 the correct Superwinch mounting plate is part #...

Hi, 2 questions: Does the SW1135220 come with a mounting bracket that would fit a Yamaha Kodiak 700? If not, do you sell a fully compatible mounting bracket i.e.: - no modifications needed? What is the part # ? | I do have a winch mounting bracket...

Will this fit this ATV properly? Blogs have complained about fitting and quality of hardware. I have a superwinch ATV2000 on a 2002 Suzuki KQ300, no problems in 12 years, easy installation too. easy clean fit on 2013 Yamaha 550EPS ??? | The...

Item # SW1125220 I was looking at this part number for a winch for my atv. One picture shows a mounting bracket and was wondering if that bracket would work with my 2016 Yamaha Grizzly 700 EPS . Thank you | There is a specific winch mount...

I have a class I hitch - 1 11/4inch How can this cover fit both 1 1/4inch and 2 | Both San Fransisco Giants hitch covers we carry, parts # HCC2124 and # OHCC2124, are designed to fit 2 inch trailer hitch receivers only. |

I would like to pull my 5 x 8 trailer with my yamaha viking but do not know if a wiring kit exists for trailer lights. I have looked but to no avail. Is something like this available? | You could use a universal style of trailer wiring for...

Is one of these kits really strong enough to secure an ATV to my trailer? I tow on rough back roads. | The 679-lb wet weight of your 2016 Yamaha Grizzly 450 ATV is well within the 1500-lb weight capacity for the Erickson ATV E-Track Tie-Down...

Just received my 12inch 4.80 trailer tires. They had 100 PSI. How much should I really run in the tires. They are on a jet ski trailer. | The Taskmaster Wheel and Tire Combo 4.80-12 part # AM30660 that you referenced has a 90 psi max rating....

Is this qty one hub or two? | The Dexter trailer axle # 84545UC1-EZ that you mentioned is sold individually. If you needed two you would need to order a quantity of two. |

I am looking for a Scissor Step that mounts from underneath the camper not on the wall the door is on. How do you mount your Aluminum Scissor Steps, 24 Wide, 31-39 Tall Code: AS24? The only place I have available to me to mount any type of...

Do the side lens come with the above lens ? | Yes, the smaller side lens does come with the Replacement Tail Light and Side Marker Lens for Optronics Combination Tail Light # A16RB that you referenced. |

DL has a free wheeling version of the DL15721. It is the DL15761. Do you sell the DL15761? I would have the unit mounted to a portable aluminum base that would be chained back to the inner most D-rings of a toyhauler to bring in a 1000 lb boat...

I would like to purchase a winch and everything I need to mount it to my ATV. I have a 2006 Yamaha Wolverine 450. I was looking at part # sw1130220. | For your 2006 Yamaha Wolverine 450 we have the custom mount # BDW15140 which mounts directly...

Looking to put a ring on with backing plate on aluma snowmobile trailer for my atv tie down. Just thinking that’s a lot of weight bouncing on the trailer,won’t it just tear a hole in the wood eventually? It’s just 1/2” sheets Thanks | Depends...

I have a 2002 bear single axel trailer with a 3500 lbs capacity. Is there any chance you can help me figure out what leaf spring I need? I can supply the vin if needed. | What you'll need to do is measure your current springs without the weight...

I got a grizzly yahama 2018 700 Eps wanting to make sure this Bulldog WInch Custom-Fit Steel ATV Winch Mount Item # BDW15185 will mount perfect. Wanting to mount Superwinch 1135220 Terra 35 3500lbs to that Bulldog WInch Custom-Fit Steel ATV...