RZ x > Rondo x > RV x > Torrent x >

Result:

Trailer Hitch that Fits 2026 Lexus RZ350e Electric

I’m looking for a 2 inch receiver that will fit my Lexus RZ350e 2026. I will be using it for a bike rack not for towing. I found the one that fits the 2026 Lexus RZ350 but it does not specify if it also works with the electric model. Can you...

Does the Curt C58VV Hitch Fit a 2026 Lexus RZ450e AWD and Affect the Hands Free Liftgate?

2026 Lexus RZ450e AWD with 2nd motor driving rear wheels. Does this Curt receiver fit? And does it interfere with the kick sensor to open the rear hatch? | Hi Stephen, Yes, the Curt Rack Receiver, Part # C58VV, is confirmed by Curt to fit...

Troubleshooting Hitch Bolts Not Fitting Weld Nuts on 2006 Pontiac Torrent

2006 Pontiac Torrent. The four bolts that go on outside dont fit into the hole. I sprayed it and cleaned it the best I could and cant get the bolts to thread. The two on the bottom middle fit with some resistance. Do you have any suggestions...

Finding Installer for Curt Hitch on 2009 Kia Rondo

A Curt Trailer Hitch Receiver for a Kia rondo 2009 what car brands aré compatible to install the tráiler Hitch | Hey Adrian, I attached a link to an installer locater that you can use to find someone to install the Curt hitch part # C11031 on...

Parts Needed to Add Brakes to 1992 Coleman Arcadia Pop-Up Camper

I want to add brakes to my 92 Coleman Arcadia pop-up. I am looking for the correct hub/drum and electric brake assemblies. The wheel bolts are 5 on 4 1/2 and the tires are Carlisle USA Trail 20.5x8-10. The current axle includes a square flange...

Bolt Size for Trailer Hitch Installed on 2006 Pontiac Torrent

Hi I was just wondering what size bolt I need for installation of a hitch on my 2006 Pontiac Torrent | For the hitches we offer that fit your 2006 Pontiac Torrent like the etrailer part # e98865 the size hardware that comes with it is M12-1.75...

Trailer Hitch Recommendation for a 2007 Kia Rondo

I am looking for a trailer hitch for a Kia Rondo that was manufactured in Dec, 2006. I dont see one in your listing earlier than 2007. Thank You | That is because you most likely have a model year 2007 Kia Rondo that happened to be built in...

Two Front M12 Bolts Will Not Tighten with etrailer Hitch e98865 On a 2007 Pontiac Torrent

I had two problems with this install. The two weld nuts under the license plate never torqued down. They were the only ones that I could tighten easily, but they never tightened up to the proper torque level. Second problem, the rear bolts...

Reese Brakeman 83501 Only Sends Power to Trailer Brakes When Using Manual Over Ride

I have installed this unit on a 2007 Pontiac Torrent. The instructions say to attach the red wire to the cold side of the brake pedal switch. On this vehicle the brake pedal switch has 3 wires. The grey wire is always hot 12v. The blue wire...

Which Brake Switch Wire on 2008 Pontiac Torrent to Connect to Tekonsha Voyager Brake Controller

I purchased this controller from you for my 2008 Pontiac Torrent. I am having a problem with finding the wire on the brake switch that goes hot when the brake is applied. The break pedal wire did not light up my 6 to 12 volts tester. I assume...

Replacement 1200 Pound Dutton Lainson Brake Winch

I have a Shorestation Jetski lift that Im told uses a 1200 brake winch. The current one has the DL logo on it. Would this unit be the correct replacement? Picture attached. | It isn't exactly the same, the housing design has changed, but...

Bike Rack Recommendation for a Camplite Trailer with an Aluminum Bumper

I just purchased the Camplite model trailer with a 2x4inch aluminum bumper. Looking for a two bike rack than will fit my conditions. | Since your Camplite Trailer has an aluminum bumper there really isn't a bike rack available that can attach...

Troubleshooting Wiring Harness # C55560 When Installing on a 2006 Pontiac Torrent

installed in my 2006 torrent power getting to the end of wire but nothing to trailer .trailer lights working fine how do I get them to work ? | The first place I recommend checking is making sure the ground connection is good on the wiring harness,...