Installation of the Roadmaster Rear Anti-Sway Bar
I have a 2003Fleetwood Pace Arrow 36B on the W22 chassis. I want to install the rear anti sway bar on it, which I feel I can do myself. My concern is the holes that need to be drilled in the frame rail. The video I watched showed the rear wheels...
Parts Needed to Install Redarc Tow Pro Elite Brake Controller in 2003 R-Vision Condor Motorhome
I just got off the phone with you guys. I was told that etrailer does not have any brake controllers to fit my vehicle. 2003 R-Vision Condor Motorhome. But the Frame is a Workhorse P-32 . Now I see according to Jameson C. Trailer brake...
Dimensions of Replacement Plastic Endcap for Ladder Rung on Stromberg Carlson RV Ladder
Is the picture of the end cap I am sending the same as your 8539 CP? | The Replacement Plastic Endcap for Ladder Rung on Stromberg Carlson RV Ladder # 8539-CP does not appear to be the same as the one in your picture. Your picture shows a screw...
Replacement Parts Available for Namsco Stainless Steel Wheel Liners # NA226H40N
Do you sell single covers rather than the set? | Currently the Replacement Center Cap # NA9130 is the only part that is separate from the Namsco Wheel Liners # NA226H40N for your Workhorse Chassis. |
Recommended For Best Replacement For Dometic Duo-Therm 620426.321 & Heat Strip
what unit will replace my 630515.321 ac unit with heat pump? I have 2 units and would be replacing both. they are 13500btu. | For the simplest and most straight forward 13.5K btu replacement of your current Dometic air conditioner we have...
Upgraded Sway Bars that Fit 2006 Itasca Built on Workhorse W Series Chassis
Which sway bars would you recommend for a 2006 Itasca 29ft | I did some digging on your 2006 Itasca and it looks to be built on a Workhorse W series chassis so for a rear sway bar you'd want the part # RM-1259-108. Then for the front bar you'd...
Options For Replacing An Advent Air ACRG11
ACRG11WO Advent A/C unit do they still make this unit or is there a replacement so I do not have to change any wiring | We do carry the Advent AC units, but the ACRG11 is an older model that has been discontinued. If you are looking to replace...
Replacement Bushings For Roadmaster Anti-Sway Bar RM-1259-106
I have a RM-1259-106 front package on my 2004 Newmar Mountain Aire Workhorse chassis. I’ve put about 4000 miles on it and just noticed that both sway bar bushings have compressed/collapsed such that there’s a visible gap. I can send pictures...
Where Is The Roadmaster TruTrac Front-Axle Trac Rod Manufactured # RM-TRACW-22
Disappointed to see roadmaster front trac bar for my 2003 w22 is made in China. Do you offer a product made in USA? | The Roadmaster TruTrac Front-Axle Trac Rod for Large Trucks and RVs # RM-TRACW-22 is manufactured in-house at Roadmaster's...
Replacement Polyurethane Bushing Kit For 1-3/4" Diameter Sway Bars
How can I get a set of replacement 1 3/4sway bar bushings? | It sounds like you are needing the Roadmaster Polyurethane Bushing Kit # RM-4109-106. This includes bushings for a 1-3/4" factory sway bar. |
Anti-Sway Bar Recommendation for 2002 Chevy Workhorse W22
We are looking for sway bars for our 2002 Chevy Workhorse W22 36ft. Do you start with just the rear sway bars or do you need front and rear? Also what is your recommendation for the right sway bar for our class A? | We'll typically recommend...
Do You Have to Reinstall the Factory Jounce Spring When Installing the AL88202 Air Helper Springs
The instruction mention reinstall of the factory jounce . Is this necessary when the 88202 comes with built in jounce? | Yes, it is necessary to relocate and reinstall the factory jounce spring when installing the Air Lift LoadLifter 5000 Ultimate...
Recommendation for Roadmaster Front and Rear Sway Bars for a 2005 Fleetwood Bounder 34F
Hi, can you advise me correct model front and rear sway bars for a 2005 Fleetwood Bounder 34F built on a Workhorse W22 chassis? Many thanks, | Yes I can! For a front sway bar to fit your 2005 Fleetwood Bounder 34F built on a Workhorse W22...
How To Install The Roadmaster Rear Anti-Sway Bar On A 2006 Workhorse W22 Chassis
2006 w22 workhorse .Installing your rear sway bar and trying to understand why the nut spacer between the spring plate and the sway bar mount plate ? And does the shock mount plate mount under the sway bar plate ? Thanks | The reason the Roadmaster...
Replacement Air Line Hose For Roadmaster BrakeMaster Supplemental Braking System
2005 32W Workhorse Brakemaster. Recurring breakage of air hose from dash to pump cylinder. Need to replace as my fix doesn't last. How do I obtain? Thanks. | You can obtain the replacement air line right here for your Roadmaster BrakeMaster...
Does SumoSpring Kit part # SSR-280-54-1 Require Drilling
Im looking at a set of Sumo Supersprings for my 2010 W22 Workhorse Class A rv. Your site say no drilling. Is this a new design because the videos i have watched show drilling into the frame. | Not all SumoSpring kits install the same. The...
Do Batteries of Excel Tankless Water Heater Alternate Directions
I installed my EX93FR and when I opened the battery box only one side had a spring. Do both batteries go in positive up? | Hey Russel, the batteries would alternate directions. |
Correct Steering Stabilizer for a 2002 Workhorse W-22 Chassis
What mounting bracket is needed for stablizer? W22 workhorse | I checked with Roadmaster and the correct Roadmaster Exact Center Steering Stabilizer for a 2002 Workhorse W-22 Chassis is part # RM32RR for GVWR's over 22K or part # RM88RR for...
Sway Bar Recommendation For 2003 Workhorse W-Series 22
Hi...I want to install the RM 1259-109 rear sway bar on my short class A motorhome instead of the RM 1259-108 because the diameter is quite a bit larger with the 109 and therefore sway is reduced about 30 more with the 109 than the 108. Your...
Installation of Frame Brackets of Roadmaster Front Anti-Sway Bar on 2004 Workhorse W-Series Chassis
I have your Roadmaster Front Anti-Sway Bar and TruTrac Rod Kit Item # RM-1259-106 that I am installing in my 2004 Newmar MountainAire RV. When I position the B424 and B425 brackets and the 3/4inch bolts there is about 1/2inch between the frame...
Steel Plate Thickness of Draw-Tite 4916 Weld On Service Body Truck Hitch Bracket
Whats the thickness of the steel on these brackets.. 1/4? | The # 4916 Draw-Tite Service Body Hitch Weld-On bracket is .375 or 3/8 of an inch thick. I've provided a photo with additional dimensions in case you needed them. |
Recommended Roadmaster Rear Anti-Sway Bar for a 2005 Newmar Mountain Aire 3778
Good Morning, Trying to determine the correct Rear Anti Sway Bar part# for my 2005 Newmar Mountain Aire 3778 Cruise Master 2004 Workhorse Chassis Vin# 5b4mpa7g243396142 A dealer is telling me its the 1259-108 but I think it may be Item # RM-1259-109....
Recommended Air Bags for a 2004 P32 Workhorse
I am about to install my Airlift 1000s in my 2004 Workhorse P32 chassis. Would a set of the 1000 HDs fit, and would there be any noticeable difference between the 1000s and the 1000 HDs? | The difference would be capacity and you would notice...
Rear Sway Bar Recommendation for a 2002 Workhorse W20
Hello, I am getting conflicting info on this bar for my 36 foot Winnebago on a W20 Workhorse chassis. Will this work? I think it should and would be better because of my length | For your 2002 Workhorse W20 chassis you would want the part #...
Filter Your Search
Contact and Help