Will Wheel Masters Lug Nut Cover Pliers Grasp Nut Covers to Remove and Install them

Question

Question:

I have a 2001 Coachman Aurora Motorhome with 19inch steel wheels! They are covered with chrome wheel covers that have two chrome false covers that unscrew to remove the covers, They look like lug nuts. Will your tool grasp these nut covers sufficiently to remove and install them? Thanks

asked by: Matt M

1

Helpful Expert Reply:

Yes, the Wheel Masters Lug Nut Cover Pliers, part # WM8211, are designed to remove any size lug nut covers. Just pinch the lug nut cover with the pliers and pull the cover off.

expert reply by: Chris O

1

Answer 1

Yes, we have the Replacement Key G384 #295-000163. This will fit Global Link door and baggage locks that accept the G384 key.

view full answer...

Answer 2

The Wheel Masters Lug Nut Cover Pliers #WM8211 is designed to remove the lug nut covers on a RV. We have used sockets to remove the covers in the past but using this tool lessens the chance of damaging the finish.

view full answer...

Answer 3

The Wheel Masters Lug Nut Cover Pliers, part #WM8211, are designed to remove any size lug nut covers. Just pinch the lug nut cover with the pliers and pull the cover off.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Will Wheel Masters Lug Nut Cover Pliers Grasp Nut Covers to Remove and Install them

Product Page this Question was Asked From

Continue Researching