How to Remove Lug Nut Caps on a Motorhome

Question

Question:

03 Fleetwood Bounder has wheel simulator lug nuts that measure at least 1 9/16. I tried a 41mm impact socket on rear wheels, but its too wide/thick to fit next to center of simulator. Do have a tool/socket that removes these simulators nuts?

asked by: Ron N

0

Expert Reply:

The Wheel Masters Lug Nut Cover Pliers # WM8211 is designed to remove the lug nut covers on a RV. We have used sockets to remove the covers in the past but using this tool lessens the chance of damaging the finish.

expert reply by: Jacob H

0

Answer 1

Yes, the Wheel Masters Lug Nut Cover Pliers, part #WM8211, are designed to remove any size lug nut covers. Just pinch the lug nut cover with the pliers and pull the cover off.

view full answer...

Answer 2

Yes, we have the Replacement Key G384 #295-000163. This will fit Global Link door and baggage locks that accept the G384 key.

view full answer...

Answer 3

The Wheel Masters Lug Nut Cover Pliers, part #WM8211, are designed to remove any size lug nut covers. Just pinch the lug nut cover with the pliers and pull the cover off.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

How to Remove Lug Nut Caps on a Motorhome

Product Page this Question was Asked From

Continue Researching