Can Lippert Ground Control TT Front Jacks Be Mounted Beyond 60 Inches?
Updated 11/12/2026 | Published 10/29/2026 >
Question:
Hi, Ive sent an email to Matthew, maybe this where I should ask my question. I have an installation question and I was wondering if thats something you could help with? Ill pose my question and please let me know where I might be able to get it answered. My travel trailer is a 2023 Flagstaff microlite 25 bsds. So it has a frame in the front. This frame from the I-beam in the front of the camper goes back 60 in and has a ground clearance of 13 in. The main I-beam that goes from the front to the rear of the camper has a ground clearance of 20 in. This mounting point would be approximately 72 in back from the front I beam. The Lippert ground control TT instructions state that the front C jack must sit in front of the 60 in. I have see two options and I prefer the one with the most clearance. Options: 1 Install the Dexter lift kit which will bring my I-beam to approximately 17 in leaving me with about 6 1/2 in clearance. Which might be okay as my current stabilizers sit at the same height and these would sit further back. 2 install the C-Jack past the recommended 60 in at approximately 72 in on the higher I beam. Note: On the image Ive attached there are two white lines. The one on the lower I-beam is the 60 in mark. The one on the higher I-beam is the 72-in. mark. You can also see in the image how low my current stabilizers sit today from factory install. I want to make sure I install this correctly so I dont have a bunch of software issues or errors appearing after installation. Im sure you guys installed this setup on a microlite 25 bsds before. Please let me know the approach youve taken in the past with this scenario on travel trailers. Im sure its not an uncommon event. One, other question. In the rear of RV there are welded bracket from the factory and look very robust and are similar to the front bracket holding the PSX2 stabilizer in photos. Can you install to these bracket in the back or do they need to grind it out. Please let me know if you need additional information. Thanks, Bryan
asked by: Bryan S
Expert Reply:
Hey Bryan, thanks for all the detailed measurements. Between your two options, I recommend sticking with Lippert's specified 60" mounting range for the front C-jacks rather than moving them back to 72". The Dexter lift kit sounds like the better route, provided it fits your trailer and gives you enough ground clearance once the jacks are installed. Moving the jacks outside Lippert's recommended mounting range isn't something I recommend since it may affect how the system operates.
As for the rear, you may be able to reuse the existing welded brackets if the mounting dimensions and bolt holes line up with the new jacks. I wouldn't start grinding anything off until you've verified that.
Have you had any issues with your factory stabilizers dragging because of the low clearance?

Jeff W.
11/6/2026
Hello, I installed the same aftermarket electronic auto level kit on my 2024 Alliance Delta 292RL. I ran into the same issue with my drop frame. My stabilizer jacks were right past the drop frame on the main I-beam. I was concerned about ground clearance if I mounted them on the drop frame part so I went ahead and mounted them on the upper I-Beam (your second white line). My camper is 34' and I have had no issues with leveling or maintaining the level with the front C Jacks in that location. I did have to cut off the 2" square tubing they had welded to the main I-beam and had the stabilizer jacks mounted to. For the rear, I did not go with the location of the rear stabilizer jacks as they were right at the rear of the camper and the C-jacks would be way to low. I just went the recommended distance from rear axles listed in the directions. Good luck with the install. I am super happy with mine and I will never own another trailer without auto level again.


Product Page this Question was Asked From
Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System - 10,000 lbs
- Camper Jacks
- Travel Trailer
- Stabilizer Jacks
- Steel
- 9001 - 10000 lbs
- Electric Jack
- 18 Inch Lift
- Bolt-On
- 5 Jacks
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Video: Review of Furrion RV Air Conditioners - Chill 15K BTU White Low Profile Heat Pump Kit - FR89TQ
- Search Results: auto leveling
- Search Results: camper jacks
- Search Results: trailer jack
- Video: All About the Timken Grease and Oil Seal
- Video: Installing the Timken Grease and Oil Seal in a 2022 Forest River Rockwood Geo Pro Travel Trailer
- Q&A: Replacement Timken Grese Seals for Dexter 3500 lb Axle
- Video: Review of Dometic RV Toilets - 420 Standard Height Elongated Bowl White Porcelain - DMC67JF
- Video: Roadmaster Comfort Ride Shock Absorbers Installation - 2021 Coachmen Apex Ultra-Lite Travel Trailer
- Video: Detailed Breakdown of the Progressive Dynamics 1800 Watt Inverter w/ Transfer Switch
- Q&A: What Is The Best Way To Tell If Trailer Brake Pads Need To Be Replaced?
- Q&A: Kodiak Disc Brake 225 Caliper Rebuild Kit
- Q&A: Looking For Leveling Kit For B&W Companion Slider 5th Wheel Hitch
- Q&A: Best Bike Rack For Carrying Two 75 lb E-Bikes On The Back Of A 2027 Brinkley Z3600
- Q&A: Best Way To Add 7-Way Plug To The Bed Of A 2025 Ford F-350
- Q&A: Replacement Cover for a Dometic Penguin II Air Conditioner Model Number 641915
- Shop: Velit Gasoline RV Heater for Camper Van - 14,000 Btu - Bluetooth Control
- Shop: Thomas Payne Heritage Dual Reclining RV Loveseat - 53-1/2" Wide - Gray
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Replacement Rubber Bushing for Kodiak Guide Bolt Sleeve - ABS Compatible - 2,000 lbs - 8,000 lbs
- Shop: SnapPad StakPad Universal Leveling Block and Jack Pad for RVs and Trailers - Green - Qty 1
- Shop: Coleman-Mach Mach-C Everest Thermostat
- Shop: Kodiak Union Fitting for Hydraulic Brake Hose - Brass - 3/16" Female Inverted Flares






Bryan S.
11/5/2026
Hi Jesse, Thank for you reply. I have snap pads on the stabilizer jacks today. And I have snagged them once in the front and losing both snap pads. This is only occurred once since I own the trailer as I'm more careful now. As to your suggested mounting location. I anticipate the height being the same with the Dexter lift kit installed and the C jacks as my stabilizers are today. I believe I'll have less chance of the c jacks dragging based on sitting 51 1/2 inches back further from the coupler than the stabilizer are now. I've also posed the same question with images to Lippert and have not heard a response back yet. Thanks, Bryan