Will B&W Gooseneck Pin Box Clear Corners of CM Flatbed
Updated 09/03/2026 | Published 08/29/2026 >
Products Featured in This Question
Question:
Hello, I will be purchasing a new fifth wheel camper soon and will be in the market for a new fifth wheel to gooseneck hitch. I am currently using a Gen Y executive and have I have nothing negative to say about it. While researching the hitches to see what was out there now I came across the bandw fifth wheel to gooseneck adapter. It has definitely peeked my interest however I am curious if it’ll work with my truck. It appears to be pretty short. My truck is a 2022 Chevrolet 3500 cab and chassis with a standard cm flatbed Will this hitch provided enough clearance between the back of the bed and the camper? Is there any helpful information you can provide Thanks for your help
asked by: Mackenzie H
Expert Reply:
Hey Mackenzie! I checked into this and I don't think the shorter appearance of the B&W 5th Wheel to Gooseneck Pin Box # BW23RV will be an issue. The B&W measures 13.5" from the center of the gooseneck ball to the forward mounting holes. The Gen-Y Executive for the Rhino pin box measures 13.541" at the same points, so the two will position the trailer in essentially the same spot front to back.
More importantly, you will need to get some measurements with the new 5th wheel since that will be different from what you have now. B&W recommends measuring from the center of the gooseneck ball to the rear corners of the flatbed, then from the center of the coupler to the front edge of the trailer. In theory, as long as the coupler to trailer measurement is greater than the ball to corner measurement, you shouldn't have any interference.
I would also compare the width and taper of the new fifth wheel to your current camper since that will have an impact on your overall turning clearance.
What fifth wheel are you looking at?
Product Page this Question was Asked From
B&W 5th Wheel to Gooseneck Pin Box - Lippert Rhino - 25K GTW - 3.25K TW
- 5th Wheel Gooseneck Adapter
- Adapts Trailer
- 5th Wheel Trailer to Gooseneck Hitch
- No Extra Clearance
- 25000 lbs
- Replaces Pin Box
- Shock Absorbing
- Lippert Rhino
- B and W
more information >
Continue Researching
- Q&A: Can B&W Gooseneck Pin Box Replace Curt Helux On 2026 Brinkley Model Z 2680
- Q&A: Does B&W 5th Wheel to Gooseneck Pin Box Include Safety Chains
- Q&A: What B&W 5th Wheel to Gooseneck Adapter Fits My 2026 Alliance Avenue 30BH?
- Q&A: How to Determine Clearance Using B&W Gooseneck Pin Box With 2009 Ram 3500 Short Bed
- Q&A: Which B&W Fifth Wheel to Gooseneck Adapter Is Best For Towing My Trailer?
- Q&A: Will The B&W 5th Wheel to Gooseneck Pin Box BW23RV Work With A 4" Offset Gooseneck Ball?
- Q&A: Gooseneck Pin Box for 2026 Alliance Avenue 25RL
- Article: 2011 Ford Super Duty with 5th-Wheel/Gooseneck Trailer Tow Prep Package
- Article: What RV AC Will Work With Your Setup? Avoid Costly Mistakes Before You Order
- Article: RV Roof Types: What Type of Roof Does My RV Have?
- Article: Fifth Wheel Hitch Combinations for Ram Trucks with RamBox (2009-Current)
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Gooseneck to 5th Wheel Adapters
- Article: Converting Your RV Water Heater to Tankless




Mackenzie H.
9/2/2026
Looking at an Open Range 3x390tbs. This camper is a wide body unit. Where current camper is just a standard width. I am using a Gen Y executive hitch on my current camper that they custom made for me 3” longer to give me extra clearance on my truck however unfortunately it is not the correct specs to fit on this open range