Replacement for Demco DM12113-95 Adjustable Channel Mount Coupler

Question

Question:

i am looking for a replacement coupler for a customer, the part number i have is DM12113-95.

asked by: Quentin H

0

Expert Reply:

Hi Quentin; the Demco DM12113-95 was discontinued in 2022 but we know it is a 2" adjustable channel coupler for a 3" channel with mounting holes 2" apart. For a similar replacement you can use the # PSA200S0303. If your customer would rather stick with Demco they now have the eZ-Latch and they can choose from a black powder coat # DM88XR or zinc # DM12688-95 finish.

expert reply by: Robin H

0

Demco Trailer Coupler
(click to enlarge)

Robin H.

12/8/2025

Hey Quentin, did the Pro Series or one of the Demco eZ-Latch couplers end up being the right fit for your customer’s trailer? Knowing which one worked could help others replacing the same discontinued model.

Reply

Answer 1

The Demco #DM12688-95 you've looked at would be a good choice. The 2 inch channel mount coupler is compatible with a 3 inch channel, and has bolt spacing of 2 inches on center. Demco is known for high quality products, you'll get years of…

view full answer...

Answer 2

The Lippert Components Bolt-On Shock Kit w/ Heavy Duty Gas Shocks - 3,500-lb (2-3/8") Axle #LC281255 are installed with the bottom of the shock in front of the rear axle and the top of the shock behind the rear axle. If you want to add shocks to…

view full answer...

Answer 3

Hello Lee, that is a good question. We do not recommend using 5/8" pins to hold the Demco #DM14040-81 coupler into the channel. The manufacturer specifies that grade 5 mounting bolts must be used in order to achieve the full 21,000 lb weight…

view full answer...

Answer 4

I believe you have Roadmaster baseplates like #RM-521453-5 instead since the Curt baseplate that's confirmed to fit your 2020 Jeep Wrangler is a different style than what you have pictured. You best bet to confirm would be to remove the…

view full answer...

Answer 5

The Aluminum Viking Series Valhalla Trailer Wheel - Black Spoke #AX02665865HDBML will almost certainly fit on your hub with 8 lugs because this wheel has an 8 on 6-1/2" bolt pattern, which is by far the most common size. However, to be…

view full answer...

Answer 6

That is an extremely unique trailer setup that would require a channel style of coupler like the part #PSA200S0303 with the bracket part #BDAC3000300 which would get welded to the front of it.

view full answer...

Answer 7

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Answer 8

Yes, it is safe to install a trailer hitch on your 2013 Ford Transit Connect XLT. The best hitch will be the Curt Class 3 Hitch #13076. We have successfully installed this hitch on a 2013 Transit Connect here at our shop in Missouri, and I have…

view full answer...

Answer 9

First I want to make sure you verify your channel mount for the Demco Trailer Coupler #DM14040-81 has a 21K or larger capacity as often times they are less like the Demco #DM15349-52 which often times people look at and think it is a channel mount…

view full answer...

Replacement for Demco DM12113-95 Adjustable Channel Mount Coupler

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching