Can RV Pendent Light # 277-000462-430 Install on Sloped Ceiling

Question

Question:

Does it his light work in a sloped ceiling and in a 12v light fixture switch in an rv?

asked by: Regenia C

0

Expert Reply:

Hey Regenia, no the light fixture part # 277-000462-430 would not work on a sloped ceiling as it does not have the ability to move or be flexible. It would look pretty awkward not hanging all the way. Would a puck light work for you? That's pretty much only thing I can think of like the part # 277-000343 as it's not directional.

expert reply by: Jameson C

0

Answer 1

Hey Dan, none of the pendent style lights for RVs would work for what you are looking for as they do not have a ability to swing at all to compensate for a sloped ceiling. They would be at an awkward angle if installed on a sloped ceiling. Better…

view full answer...

Answer 2

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Hey Danielle, the Gustafson RV LED Pendant Light #277-000462-430 that you referenced does have an LED "bulb" but it is not replaceable. It's basically has a board with 6 LEDs on it that produce light. The panel is not a standard type of…

view full answer...

Answer 6

You sure do Greg! Which is why the MORryde X-Factor Crossmember for Standard Frame Hangers item #MR33WR comes with longer suspension bolts. These bolts will replace the ones currently being used on your trailer's spring hangers. The X-Factor…

view full answer...

Answer 7

The mounting holes of the part #RVPL7CB that you referenced are 4-3/4 inches apart on center. This wouldn't match up perfectly to the mounting holes of your trailer so you could raise or lower the light in relation to it's current mounting…

view full answer...

Answer 8

That’s a great plan, Cheryl. For your camper with 6-lug, 5,200-lb axles, the #MXS87FR is ideal - stylish, aluminum, and rated 3,420 lbs at 80 psi. For your smaller utility trailer with 5-lug, 3,500-lb axles, go with the #MXS67FR. It carries 2,150 lbs…

view full answer...

Answer 9

It does, Dawn. The #MXS67FR is bead-balanced and pre-mounted from the factory, complete with high-pressure valve stems. It’s ready to bolt right onto your 5 on 4-1/2 hubs with standard 1/2-20 conical-seat lug nuts. The tires are 205/75R15 radial; is…

view full answer...

Answer 10

That’s a great setup, Tanya. Yes, this 100W etrailer panel #E28VV includes an SAE cable that will plug directly into your Geo Pro’s “solar on the side” port. And since the panel delivers about 4.8 amps at peak, it’s well below the 10A limit of your…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Can RV Pendent Light # 277-000462-430 Install on Sloped Ceiling

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching