Will The MaxxFan Deluxe Work With Lift/Fan Wall Buttons From Old vent?

Question

Question:

I have a 2016 Tiffin with two vent fans wired in. They both have a vent lift and a vent fan button. Will the wiring tie into MA00-07500K? I know it has a remote, but I would also like the current wall buttons to work as they are now.

asked by: Phil F

0

Expert Reply:

Hello Phil, thanks for getting in touch. The MaxxFan Deluxe # MA00-07500K is a great choice for a vent fan and it can be used to replace your current vents. This vent can only be operated with the manual controls on the vent itself, or with the included remote. If you have a wall switch for the old vent it would not work with the new one. The only way to use a switch with this vent would be with a simple on/off switch but even that is not recommended because the vent is designed to have constant 12v power.

expert reply by: Jesse M

0

Jesse M.

12/15/2025

Hey Phil, how did things go with the MaxxFan Deluxe on your Tiffin? Were you able to get comfortable using just the remote and vent controls? Your update could make it easier for others looking to replace their wired fans.

Phil F.

12/16/2025

@JesseM The install went really well. It was an easy job once I got past all the old sealant on the roof from removing the old fans. The remote is a bit of a mystery. We have to be right under the fan to get it to turn on and off. Sometimes I have to press the open button a few times to get the fan to turn on. Also, it will change the flow direction after it is closed. If I have the air being pulled out, then close it; it changes it to air in the next time it is turned on. Is that normal? Other than that, we love the fans.

Jesse M.

12/16/2025

@PhilF Hey Phil, I'm glad to hear you are a "fan" of the fans! Sorry to hear about the problems with the remote though. Do all of the buttons on the vent itself work like they are supposed to? If so, this points to a problem with the remote itself. Its normal for the fan to change direction when you close the vent, but it sounds like the buttons on the remote might not be responding like they should. In this case, a new remote should fix that. We have the remote available as part # MA00A01150K.

Phil

12/16/2025

@JesseM The buttons on the fan itself work as they should. Does the remote need to be directly under the fan for it to work? I have it on the wall opposite the fan side.

See All (6) Replies to Jesse M. ∨

Answer 1

Hey Jared, the length of the Replacement Support Arm for Thule Omnistor 5200 Motorized Awning #LC62TF that you referenced is 1.9 meters.

view full answer...

Answer 2

We do have the Replacement Support Arm #LC62TF which is the Lippert part number 656608.

view full answer...

Answer 3

Hey John, thanks for reaching out! I unfortunately don't have the length of the Replacement Support Arm for Thule Omnistor 5200 Motorized Awning #LC62TF, but what I can say is this is designed to fit the Thule Omnistor 5200 Motorized Awning so if…

view full answer...

Answer 4

Hello Ryan. It may be possible to replace the arm assembly for your awning, but there is no way to look up your camper to know what brand and model of awning it is equipped with. The arm assemblies are brand specific so please confirm for me what…

view full answer...

Answer 5

Hi Christopher, The Replacement Support Arm for Thule Omnistor 5200 Motorized Awning #LC62TF should come with two arms and not just one, it will include everything you see in the picture attached below. This comes with two wall brackets to lock the…

view full answer...

Answer 6

The Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans #FVK8017-00 is the correct replacement for all bow-tie style bracket, motor, blade assemblies. This will fit your model 5000RBT fan (also known as #FV802250).

view full answer...

Answer 7

Both the #MA00-07500K and the #MA00-07000K can be used with a wall control setup but they only come with a remote control. So for either you'd also need the wall controller #MA59FR. With this installed you'd be able to control the fan with…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Will The MaxxFan Deluxe Work With Lift/Fan Wall Buttons From Old vent?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching