Looking for Replacement Clearance Light Lens for Grand Design 420714

Question

Question:

Looking for a replacement lens for this Grand Design part number LIGHT EXTERIOR LED 2 DIODE RED CLEARANCE W/GASKET Part Number: 420714 Cracked the lens with brush washing it. Want to pop cracked one off and put new one in its place. Hoping this part lens will fit OEM Replying to Jameson C adding pictures. Did not see another way to upload the pictures.

asked by: James L

0

Expert Reply:

Hey James, that light looks like the # MCL40RB which means for a replacement lens you'd need the part # A44RB.

expert reply by: Jameson C

0

James L.

9/27/2024

Youb are the man. Thank you for sourcing the replacment cover. I appreciate your help. JL

Jameson C.

9/29/2024

@JamesL Glad I could help!

Answer 1

You will definitely want to go with the Road Armor Shock Absorbing Equalizer Kit #LC696740 over the MORryde as the Road Armor has more travel and will provide a smoother ride. Then, in regards to shackle straps I'm not sure what you mean by which…

view full answer...

Answer 2

Hey David, thanks for reaching out. The only TPMS sensors that sync with your GMC truck are the OEM sensors from GM that mount inside the wheel, and those are not something we carry here. You aren't going to find screw on sensors that work with…

view full answer...

Answer 3

Well you've reached out to the right place, Kaivon - I'd be happy to help you navigate upgrading your trailer suspension! All three of those suspension kits you asked about are great, but my recommendation is using the MORryde Rubber…

view full answer...

Answer 4

The SAE number you provided in your question isn't always the most accurate way to determine a correct replacement assembly. This is simply because it does not refer to the actual light part number, but to various safety guidelines that it meets.…

view full answer...

Answer 5

Hey Brian, we do not have a thermostat control setup for your roof vent. If that's something you needed you'd have to go with a different vent assembly like the MaxxFan part #MA00-04002K.

view full answer...

Answer 6

The correct replacements we offer for the Glo Brite Marker Lights 118A and 117R is the Trailer Clearance or Side Marker Light part #MC44AB for amber and part #MC44RB for red.

view full answer...

Answer 7

I attached a wiring diagram for the Solera Power Awning Switch Kit #LC285500 for you to check out.

view full answer...

Answer 8

The SAE number isn't the best way to pick out replacement lenses for trailer taillights since that isn't actually a part number. However, I did find a replacement lens with SAE P2A 01 DOT on the front of it. Check out the part #A44RB. If this…

view full answer...

Answer 9

The Commercial Grade Battery Box for Dual 6V Batteries #329-HM426 is a hard molded plastic so you could definitely cut a hole in the lid and run a hose from it to a vent like the Valterra RV Battery Box Vent with Cover - White Cover #A10-3300-05 (…

view full answer...

Answer 10

Hey John, I hate to be the bearer of bad news but both the PowerGear controller and Lippert controller replacement (372854) for the PowerGear controller have been discontinued. At this point you would need to see if you could find a replacement…

view full answer...

Answer 11

I have some measurements for you which will allow you to verify if the Replacement Amber Lens #A44AB will fit your 2023 Grand Design Imagine XLS 17MKE. This lens is 4" long by 1-1/2" tall, see image below. Unfortunately, only Grand Design…

view full answer...

Answer 12

Normally the SAE number isn't a reliable way to pick out replacement lenses, but we know that the #A32RB is the correct replacement for a lens marked SAE-A-P2-DOT-02 like what you have. For an all new assembly you'd want the part #MC32RB.

view full answer...

Looking for Replacement Clearance Light Lens for Grand Design 420714

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching