What Are The 2 Wires On The SeeLeveL Sensor SE78VR For?

Question

Question:

Can you tell me what the two leads do? I would like to connect to this with an ESP8266 not your monitor. Eric

asked by: Eric C

0

Expert Reply:

Hello Eric. For the SeeLeveL Sensor for RV Holding Tank Monitor # SE78VR, the blue wire is for the tank sender signal and the black is for ground. As long as they are wired correctly, they will work with any monitor including your ESP8266.

expert reply by: Jesse M

0

SeeLeveL Sensor Wire Function
(click to enlarge)

Eric

9/24/2024

Thank you Jesse. How does it get power? And what voltage does it need to be powered with?

Jesse M.

9/24/2024

@Eric Power is carried thru the blue signal wire. They need 12v power to operate. Take a look at the installation instructions in the link below: https://www.garnetinstruments.com/wp-content/uploads/2022/09/709-RVC-NLP-Manual_v7.1.pdf

Answer 1

Campers with either 30-amp or 50-amp connections are all going to be 120 volt. The connectors they use can be wired for either 120 volt power or 240 volt power which is why you see several people damage their campers as they try and plug into an…

view full answer...

Answer 2

Mike, unfortunately not. The SeeLeveL Sensor for RV Holding Tank Monitor #SE78VR is designed to be used with the SeeLeveL RV Holding Tank Monitor #SE34VR, so it's not going to work with your Simarine Pico Tank Monitor.

view full answer...

Answer 3

The SeeLevel systems will require you to replace your current monitor in order to properly read the sensors and operate. There are quite a few different combinations of monitors and sensor strips so I'd like to know exactly what you're…

view full answer...

Answer 4

Spring Hanger location dimensions are normally figured by the manufacturer and provided with the spring hanger kit, that includes all of the parts for installing the springs on the trailer frame. I have provided a chart that shows the spring hanger…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

What Are The 2 Wires On The SeeLeveL Sensor SE78VR For?

Product Page this Question was Asked From

Continue Researching