Replacement Box with LED Lid for Engager Breakaway Kit

Question

Question:

Do you sell just the replacement lid for the 20098 Endurance™ Engager™ LED Test Break Away Kit?

asked by: Mike L

0

Expert Reply:

No, I am sorry we do not. The lid for the Replacement Box with LED Lid for Engager Breakaway Kit item # HM20121 will fit the 20098 Endurance Engager LED Test Break Away Kit. It's designed for the Item # 20099 but they're the same size.

expert reply by: Jerred H

0

Answer 1

We do offer a replacement battery box with LED lid for the Hopkins Engager Breakaway box. The part number for the box and lid is #HM20121 and the part number for the battery itself is #HM20008.

view full answer...

Answer 2

If the pin on the breakaway switch is pulled or broken then yes you should have 12 volts entering and exiting the switch as this is what will engage the brakes on the trailer. The breakaway switch on your trailer is a normally open circuit which…

view full answer...

Answer 3

The Aluminum Viking Series Valhalla Trailer Wheel #AX02350545BMFL that you referenced actually includes the sleek matching center cap (pictured below) and for compatible stainless steel lug nuts the Lionshead #LHLR103 will work perfectly. This will…

view full answer...

Answer 4

There are differences that the colors reference for the Type 1 Propane connectors based on the spring tension and flow rate. The light green connectors are rated for Rated for 200,000 Btu per hour. The black are rated for 70,000-100,000 Btu per hour.…

view full answer...

Answer 5

A 3/4 inch socket is right at 19 mm and a 11/16 socket is right at 17.5 mm. An 18 mm socket would be right in the middle between the two and should work well for you.

view full answer...

Answer 6

Sleeve-Lock A-Frame Trailer Coupler #CA-5296H-B is made for weld-on installation. We do have A-frame couplers that bolt on, like #BD44150WH301 and others shown on the linked page, but none of these is a sleeve lock type. Drilling the coupler to allow…

view full answer...

Answer 7

There isn't really a lot of differences between the Hopkins 7-Way RV Style Connector with Molded Cable - 8' Long - RV Standard #H20046 and Hopkins 7-Way Blade Style Connector with Molded Cable - 8' Long - Auto Standard #HM20041. Both are…

view full answer...

Answer 8

No, I am sorry we do not. The lid for the Replacement Box with LED Lid for Engager Breakaway Kit item #HM20121 will fit the 20098 Endurance Engager LED Test Break Away Kit. It's designed for the Item #20099 but they're the same size.

view full answer...

Answer 9

To replace the motor on the LCI Pump 650057 we have the Replacement Motor #LC167576.

view full answer...

Answer 10

Yep, your 2,200 lb Timbren Axle-Less Trailer Suspension #ASR1THDS03 is 100 percent compatible with and able ot use the 6-lug hub you asked about, which is the following part number: - Easy Grease Trailer Hub and Drum Assembly #AKHD-655-35-EZ-K This…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Box with LED Lid for Engager Breakaway Kit

Product Page this Question was Asked From

Continue Researching