Recommended Replacement LED Trailer Tail Lights

Question

Question:

Please see the attached Photos... do you have this light available. it appears to be the same light except it is the rubber grommet style for mounting.

asked by: Dustin B

0

Current LED Lights
(click to enlarge)

Expert Reply:

I agree Dustin, the TecNiq LED Trailer Tail Light # TN33XR does appear to be the exact same light as to what you're looking for. But since yours mounts in the rubber grommet, I'd suggest just popping the rubber grommet out and screw the new ones into your trailer.

expert reply by: Bryce D

0

Answer 1

To add the reverse function on your trailer you need a 7-Way connector and enough wiring to run from the front to the back of your trailer. Here are the parts you need to get the wiring from your tow vehicle back to the TecNiq LED Trailer Tail Light…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hello Tim, Happy to help you get the right light. The information that I found on the DOT 16P2ST2 T35 16, it appears to be a 6-inch oval LED combination light serving as a stop, tail, turn, and reverse signal. For a replacement you can use the TecNiq…

view full answer...

Answer 8

Hey Michael! When you're choosing a weight distribution hitch the most important factor is the tongue weight of the trailer. It looks like the dry/unloaded tongue weight of a Brinkley Z Air 297 is 924 lbs. Once you add batteries and propane you…

view full answer...

Answer 9

The Axletek 44-GG is a 10 inch by 2-1/4 inch 3,500 lb axle brake assembly which we offer with the part #AKEBRK-35L-SA.

view full answer...

Answer 10

Hi Michael, if you're looking for a surface mount light instead of a flush mount, I recommend the TecNiq LED Trailer Tail Light with Stop, Tail, Turn, and Reverse functions, Part #TN75XR. Since it mounts to the outside of the trailer, you…

view full answer...

Answer 11

It sure does Chris! The Peterson LumenX LED Trailer Tail Light item #PE76UR does indeed have the functions on individual wires. The connectors at the ends of the light work with a AMP style connector. The LumenX LED Trailer Tail Light item #PE76UR…

view full answer...

Answer 12

Hey Carlos, the closest option we have would be the Tandem Axle Jeep Style Trailer Fenders part #HP62VR which is 72 inches long and 10 inches wide. It is also diamond plate like you wanted but it is not painted.

view full answer...

Recommended Replacement LED Trailer Tail Lights

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching