Will the 2-Tang Clevis for BulletProof Hitches Adjustable Ball Mount Work w/ BulletProof Hitches?

Question

Question:

I already have a bulletproof 6inch hitch. Can I use this clevis pin attachment to regularly tow a pintle trailer, or should I get a separate pintle hitch specifically for my trailer?

asked by: Brent

0

Expert Reply:

You should have no problem using the 2-Tang Clevis for BulletProof Hitches Adjustable Ball Mount item # 358CLEVIS on your current ballmount. I say should because I have no idea which one you have but I do have the bolt hole measurements so you can confirm before ordering.

The distance between mounting holes from center to center is 2". So long as your Bulletproof 6" hitch has the same spacing you will good just purchasing the item # 358CLEVIS. I have attached a dimensional diagram below.

It will definitely work on the BulletProof Hitches 2-Ball Mount for 2" Hitch item # MD204 or item # MD254.

expert reply by: Jerred H

0

BulletProof Clevis Measurement Chart
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Hi Ray! The MORryde GooseTech 5th Wheel to Gooseneck Pin Box for 11.5K to 14K Trailers #MR74MV can definitely be used in a short bed 3/4 ton pickup, like your 2024 Ram 2500. Just be aware that not all trailers have a tapered nose and you may not get…

view full answer...

Answer 9

Hey Bill! The Rebel is the heavier duty SumoSprings jounce springs and they have the higher weight rating at 3,000 lbs #SS64VR or 5,000 lbs #SS27GR. I usually only recommend these heavy duty versions if you have a lot of weight in the truck bed or on…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Will the 2-Tang Clevis for BulletProof Hitches Adjustable Ball Mount Work w/ BulletProof Hitches?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching