Should Hitch Pin Hole Be Exact Diameter as Hitch Pin

Question

Question:

I have a 3 hitch on my RV and use two reducers 2 1/2 and 2 to bring it down to size required for Blue Ox tow hitch. The RV hitch as 3/4 pin hole while the two reducers have 5/8 pin holes. I therefore have to use 5/8 pin which of course wiggles in 3/4 hitch hole, resulting in wear both on pin and holes beginning to enlarge. Do you have reducers that have 3/4 hole in them so I can place 3/4 pin through all three?

asked by: Lothar

0

Expert Reply:

Some wiggle is actually pretty normal. It's not recommended to have a pin that fits exact to the hitch pin hole as it would make it very difficult to line up the hitch pin and the hole in the shank of the hitch accessory.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hello Joe, Thank you for reaching out! The Power Mountain Tallboy Off-Road Bottle Jack - 11-5/16" to 27-1/16" Lift - 12 Tons #PM94FR does have the capacity you’d need, but since your fifth wheel’s frame sits about 25" off the ground,…

view full answer...

Answer 11

Hey Chris, that information is what we need to confirm. I reached out to Lippert with that LCI number and the response was you have a 1621 with 15.5k weight capacity. Curt Flex Air 5th Wheel Pin Box #LC328492 is going to be a direct replacement and…

view full answer...

Should Hitch Pin Hole Be Exact Diameter as Hitch Pin

Continue Researching