Is There Drilling Needed to Install Hitch on 2023 Subaru WRX
Updated 06/13/2023 | Published 06/12/2023
Question:
It says its compatible with the 2023 wrx. Is there any way to confirm ground clearance once installed, and how much further it comes out relative to the bumper? Any more information on what specific drilling will be required for the install?
asked by: Michel
Helpful Expert Reply:
The Draw Tite hitch # 76271 definitely does fit your 2023 Subaru WRX and when we installed it we found that the distance from the bottom of the hitch to the ground measured right at 11-1/2 inches. From the center of it's hitch pin to the furthest point out on the rear bumper measures 5-1/2 inches. There will be two holes that will need to be drilled on the chassis of the vehicle. You can see where exactly in the attached install instructions and install video.
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 3500 lbs WD GTW
- 2 Inch Hitch
- 525 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Set up: Draw-Tite Max-Frame Trailer Hitch Receiver on a 2022 Subaru Forester
- Q&A: Trouble Getting Hitch Pin Holes To Line Up Using Kuat Shank Adapter # D101
- Q&A: Recommended Hitch for a 2022 Subaru WRX
- Q&A: Comparing EcoHitch and Draw Tite Hitch for 2020 Subaru Forester
- Q&A: Recommended Hitch for a 2022 Subaru WRX
- Q&A: Comparing Draw-Tite and Curt Trailer Hitch Receivers For a 2019 Subaru Forester
- Video: Setting up the Curt Trailer Hitch Receiver on your 2020 Subaru WRX
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: EcoHitch Invisi Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Roof Rack
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Installing the Curt Trailer Hitch Receiver on a 2025 Toyota RAV4
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Article: How to Choose the Right Trailer Hitch Class
- Video: Inside Look at TowSmart and Oris Hitches with the Manufacturer
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Measure for Trailer Hitch Drop
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Search Results: hitch bike racks
- Shop: Brake Controller
- Video: Mount: etrailer Trailer Hitch Receiver on a 2024 Subaru Crosstrek
on Trailer Hitch
