Width Of The Roadmaster Adapter Kit for Blue Ox Motorhome Mounted Tow Bars # RO64FR

Question

Question:

what is the width of the RO64FR adapter where the pin goes through?

asked by: Len E

0

Expert Reply:

I've drawn up a diagram showing the dimensions of the Roadmaster Adapter Kit for Blue Ox Motorhome Mounted Tow Bars # RO64FR below. The pin holder portion of this adapter is 2-1/8" wide and 1-1/2" in diameter.

expert reply by: Kevin C

0

RO64FR Dimensions
(click to enlarge)

Answer 1

Hello Gary, Since you identified that the base plate on your car is the Roadmaster Direct-Connect Base Plate Kit - Removable Arms #RM72VT, and you already have Blue Ox tow bars, you’ll need the Roadmaster Base Plate Adapter Brackets for Blue Ox…

view full answer...

Answer 2

Hey Don, Nope, there is no strength or mechanical design benefit to using the Universal Triple-Lug Tow Bar Adapter for Roadmaster Direct-Connect Base Plates #RM62ZR instead of the Roadmaster Base Plate Adapter Brackets for Blue Ox RV-Mounted Tow Bars…

view full answer...

Answer 3

Hey Craig, yes you can use blue Loc Tite with the install of the RO64FR. The red is permanent but if you can get a torch on it you can melt it so that it can be loosened.

view full answer...

Answer 4

I have a couple options which will allow you to adapt your Blue Ox tow bars to fit a Roadmaster base plate. First the Tow Bar Adapter #RM62ZR will fit in place of the direct connect arms you got with your base plate. Another option is the Adapter Kit…

view full answer...

Answer 5

The Chevy/GMC trucks underwent a generational design change for the 2020 model year, so the base plates that fit your 2015 GMC Sierra 2500 will not fit your 2021 GMC Sierra 2500. As of this writing, Blue Ox does not have an option for base plates…

view full answer...

Answer 6

It looks like you have a car side in the picture. You can get a set of replacements using #RM-222. I would recommend replacing both so they wear the same. And for reference the tow bar side is #RM-221. The individual left and right sides are not…

view full answer...

Answer 7

We do have the quick disconnect base for your Roadmaster Falcon 5250, the Roadmaster Base Bar #RM-067. Each of the other parts of the quick disconnects are also available should you need them; the Tow Bar Quick Disconnects - Car Side Only #RM-222,…

view full answer...

Answer 8

When towing a vehicle behind an RV, you would first need to install base plates on the vehicle being towed. If you have a 4 cylinder you would need Roadmaster XL Base Plate Kit, #1523-2. For a 6 cylinder, you would need Roadmaster XL Base Plate Kit,…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

To measure for safety chains you will want to have the trailer hooked up to your tow vehicle with it just about jack knifed as this is the furthest the safety chains will be stretched. You will measure from one side of the tongue where you will be…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Width Of The Roadmaster Adapter Kit for Blue Ox Motorhome Mounted Tow Bars # RO64FR

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching