Where Should Replacement Ramp Door Seal Be Installed On Trailer

Question

Question:

I have a enclosed trailer with a ramp gate. Is it best to apply the weather stripping to the ramp door or to the inside frame encloser? Please advise Thanks

asked by: Bruce K

0

Expert Reply:

The Ramp Gate Seal Kit for Enclosed Trailer Ramp # SR35FR can be installed in either location. Personally, I would keep it off the ramp door since you're more likely to damage it as you walk or move things across the ramp. Inside the frame enclosure would be the way to go.

expert reply by: Robin H

0

Answer 1

For an RV door you'd need a strut like the part #372-5300-10 which has a 10 lb strength and then to mount it you'd need the mounting bracket kit part #372BR-1020 for a flat bracket or the part #372BR-1015 for a set with angled mounts. We…

view full answer...

Answer 2

Yes it does, Jerry. Check out the D-Shaped Rubber Bulb Seal for Slide Out or Ramp Gate #SR32ZR. This bulb seal has the same dimensions as #SR26FR but is 30' long.

view full answer...

Answer 3

Hey Shyanne, thanks for reaching out again! The best way to replace the gas spring on your entry door is to look for any identifying markers on your current gas spring and try to match it with what you have. For example, the Gas Shock #372-5300-10 is…

view full answer...

Answer 4

A typical RV entry door gas strut ranges from 10-20lbs in pressure. We carry both a 10lbs #372-5300-10 and 20lbs #372-5300-20 that you can use. Really it just comes down to preference and the climate. If you're in a windy climate going heavier…

view full answer...

Answer 5

Yes, we have some parts that can help. We have the Replacement Handle Assembly for Polar Cam-Action Latch Kits - Zinc-Plated Steel #158-100. And the Handle Assembly for Polar Cam-Action Latch Kits - Aluminum #PLR158-100-A. Lastly the Replacement…

view full answer...

Answer 6

Hey Chad, You'll need an air distribution box to go with your rooftop unit #ADV79FR to get the other half of the system. You could go with the #ACDB if you want the controls built into the air distribution box or the #ACRG15 if you'd prefer a…

view full answer...

Answer 7

I do have a solution for you, however the Draw-Tite 5" Offset Ball #19308 mentioned in your question is not compatible with B&W gooseneck hitches. There a few compatible offset balls for your B&W Turnoverball Gooseneck Hitch, depending…

view full answer...

Answer 8

Hey Rick. Unfortunately that's correct the Wesbar Tail Light 271594 has been discontinued. Our best option for replacing it is the LED Trailer Tail Light item #STL36RB for the passenger side and item #STL37RB for the driver side. The Wesbar light…

view full answer...

Answer 9

The Furrion #FMCM15SS is a great appliance that will meet your needs. I researched the dimensions of your original Dometic and discovered they are 29 15/16" wide x 16 7/16" tall x 15 3/8" deep. The Furrion I'm recommending will fit…

view full answer...

Answer 10

There isn't a specific height from the trailer floor recommended to mount the E-Track. My gut feeling is that if 3 feet is too low and 4 feet is too high then 3-1/2 feet might be perfect. Another option is to mount E-track pieces vertically along…

view full answer...

Answer 11

Nick, absolutely. Many vanlifers wire the Velit 2000R 12V AC Unit #VE87QV so it runs while the alternator tops off the batteries. It keeps the living space cool while driving long stretches, and when you park, your bank’s already partly replenished.…

view full answer...

Answer 12

I attached a picture I got from Buyers Products that has the dimensions of the Buyers Products Hook and Keeper for Enclosed Trailer Door #BP64FR that has the dimensions you are looking for.

view full answer...

Where Should Replacement Ramp Door Seal Be Installed On Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching