Will the Flint Hill Goods Trailer Dolly Work with a 2" Coupler

Question

Question:

Will this accommodate a 2inch ball.

asked by: D N

0

Expert Reply:

The Flint Hill Goods Trailer Dolly part # FHG84ZR will sit inside a 2" coupler but the coupler won't be able to latch so it could just pop off. If you want to use this dolly with a trailer that has a 2" coupler, I recommend replacing the 1-7/8" hitch ball with the 2" Hitch Ball part # 19258 but please keep in mind this won't increase the capacity of the dolly which is 600 lbs of tongue weight. It will really come down to how much you can physically pull.

expert reply by: Conner L

0

Answer 1

We don't sell a 2-5/16 inch hitch ball with a 3/4 inch shank, but since a tow dolly is only used for small trailer movements across a parking lot your current hitch ball should work just fine. When using a tow dolly the tongue weight alone of the…

view full answer...

Answer 2

We do not, we only carry the #RA20BALL for the rackem tow dolly. Realistically this is the only size you would need. If you were in a situation where you needed the coupler to be latched on to the ball of the dolly you would be in bigger trouble than…

view full answer...

Answer 3

The best type of trailer dolly for your application of moving an 850-lb utility trailer is a 2-speed hand-crank dolly like the Trailer Valet 5X Swivel Jack and Trailer Mover #STC-V211. This is both a trailer-mounted tongue jack and a…

view full answer...

Answer 4

There is an option like the Flint Hill Goods #FHG84ZR which would work with 1-7/8" and larger hitch ball couplers, but there is no dolly that'll work with a pintle hook on a trailer. The #FHG84ZR includes a 1-7/8" hitch ball, though you…

view full answer...

Answer 5

With the trailer only weighing 2,200lbs you'd be looking at roughly a 220lb tongue weight if the trailer was fully loaded. I have two different trailer dolly options depending on your needs. If you want a standard no-frills option the Flint Hill…

view full answer...

Answer 6

If you really wanted to you could remove the 1-7/8 inch ball of the Flint Hill Goods Trailer Dolly part #FHG24ZR and install a different ball size...BUT it won't gain you anything by doing so and would only prevent you from using it with a…

view full answer...

Answer 7

To determine if your motorhome has the Tiffin air brake setup or Freightliner BrakeSync you'll need to look at the rear and see if there's an quick disconnect fitting for your air line. The standard Tiffin air coupler fitting would look like…

view full answer...

Answer 8

There is no danger of the Brophy Cable Camper Jacks #CJ31 flipping the camper over when you are using them; you just need to ensure they are properly used and aren't overloaded past their 1,000 lb (combined) capacity. These jacks have a tripod…

view full answer...

Answer 9

I pulled the Fulton F2 Swing-Up Trailer Jack, part #F1413020134, from our warehouse and took a photo and some measurements for you. This jack has dual 7 inch wheels and features a sidewind handle. The jack has an adjustable mount, and is a bolt-on…

view full answer...

Answer 10

Yes, it will! The Flint Hill Goods Trailer Dolly item #FHG24ZR will work just fine with your 2" coupler even though it has a 1-7/8" hitch ball. Due to how slow you would be moving and how light dollies are it's not important for the…

view full answer...

Answer 11

I do have an option for you but we don't have a roof vent cover that would fit over the MaxxFan Deluxe Roof Vents like part #MA00-07500K since it already has one built-in. If you want to use a separate large roof vent cover like the MaxxAir II RV…

view full answer...

Will the Flint Hill Goods Trailer Dolly Work with a 2" Coupler

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching