Will The UWS Toolbox # UWS08298 Fit With The Canister From A RetraxPRO MX Tonneau cover

Question

Question:

I have a 2021 F350 w/ 8foot bed. Will this tool box fit under a Retrax pro MX retractable cover or will the canister hit the box?

asked by: Jason M

0

Expert Reply:

The back portion of the UWS Secure Lock Truck Bed Chest # UWS08298 is 12-1/2" tall and the canister for the RetraxPRO MX Hard Tonneau Cover # RT80384 is going to sit 11-5/8" down from the top of the bedrails. From what I can find online a stock F-350 has a bedrail height that's approximately 21.1" so you would run into a clearance issue and only be able to place the toolbox up against the canister.

expert reply by: Kevin C

0

Retrax Cannister Dimensions
(click to enlarge)

Answer 1

Hey Tod, the two UWS boxes have different shapes and capacities. If you check out the attached pictures you can see the differences between the part #UWS08298 and #UWS01044 to get a better idea. The #UWS01044 has a slightly smaller capacity at 8.2…

view full answer...

Answer 2

The BAKBox 2 Collapsible Truck Bed Toolbox #BAK92120 is specifically designed to mount to the side rails on BAK tonneau covers which are going to be different on your REV cover. So you will need a toolbox which fits down inside the bed like the UWS…

view full answer...

Answer 3

BAKFlip tonneau covers are going to interfere with opening the lid of the UWS Truck Bed Chest - Wedge Series - Offset Lid - Notched Box #UWS01048. Instead you can use a toolbox like the UWS Truck Bed Chest #UWS08297 or the #UWS08298 for black.

view full answer...

Answer 4

In order to find the best toolbox for your setup you'll need to do some measuring, since you have a tonneau cover you'll measure your clearance from the top of the bed to the bottom of the cover while closed and since you have a fifth wheel…

view full answer...

Answer 5

The height of the UWS Truck Bed Chest - Secure Lock Under Tonneau Series - 8.85 cu ft #UWS0829 when the lid is fully open from the bottom to the top is 31 inches tall.

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

When people install truck bed tool boxes like the part #UWS08298 in the bed of trucks like your Tacoma normally holes are drilled through the floor of the box and the truck bed and hardware is ran through both which secures it. We have this as an…

view full answer...

Answer 8

The canister of the Pace Edwards JackRabbit Hard Tonneau Cover #311-JRC95A17 measures 9.75" wide x 9.25" in deep. That would be how much of your truck bed it would take up.

view full answer...

Answer 9

The Pace Edwards UltraGroove Retractable Hard Tonneau Cover #311-KRD7936 is a confirmed fit for your 2022 Ram 3500 with an 8' bed but you'll need the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack #Y01151-58 instead of the #Y01151-5855…

view full answer...

Answer 10

I spoke to my contact at Thule and she informed that the number you listed isn't a part number, but that based on that she could tell about how old your rack is and what would be the correct part you are looking for. The replacement bolt you need…

view full answer...

Will The UWS Toolbox # UWS08298 Fit With The Canister From A RetraxPRO MX Tonneau cover

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching