Can the Drop Leg Plunger Pin Be Relocated on the Square 10K Direct Weld Jack
Published 02/02/2023
Products Featured in This Question
Question:
We have two jacks connected in tandem. Problem is, the leg handle on one jack is on the wrong side to operate easily. Can the inner tube be turned 180 degrees to get the operating handle on the other side?
asked by: Paul
Expert Reply:
I do have an option for you but the drop leg plunger pin cannot be relocated, you will instead need to purchase a different jack with plunger pin in the correct location for your needs. The Square 10K Direct Weld Jack for example is offered with two different plunger pin locations, part # TJD-12000SP-R2 for side or part # TJD-12000SP-F2 for front.
In other words, you'd need to remove the existing jack and weld a new one into place with the correct plunger pin orientation.
Product Page this Question was Asked From
Square Trailer Jack w/ Handle - Side Pin Drop Leg w/ Spring - 12-1/4" Lift - 10,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- 5th Wheel Trailer
- Gooseneck Trailer
- Side-Mount Jacks
- 9001 - 10000 lbs
- Manual Jack
- 26 Inch Lift
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Continue Researching
- Search Results: deemaxx trailer brakes
- Search Results: master cylinder
- Search Results: 12k jack
- Search Results: fender
- Search Results: titan model 10 master cylinder
- Search Results: 22575r15
- Search Results: 205 75r15
- Shop: etrailer Square Sidewind Trailer Jack - Foot Release Drop Leg - 13-1/2" Lift - 12,000 lbs
- Video: Review of etrailer Trailer Jack - TJDDP-20000SP-F
- Shop: Square Trailer Jack w/ Handle - Side Pin Drop Leg w/ Spring - 12-1/4" Lift - 10,000 lbs
- Q&A: Replacement Inner Member for a Dexter Model A60/A75/XR84 Brake Actuator
- Q&A: Can Internal Rod Be Replaced for Heavy Duty Bulldog Jack
- Q&A: What Info is Needed to Determine How Much Battery is Needed for RV For 3 Days
- Shop: Battery
- Q&A: Replacing A TDE Model LP7000 Actuator
- Shop: Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K
- Shop: Tandem Axle Trailer Fenders for Enclosed Trailers - Aluminum - 14" to 15" Wheels - Qty 2
- Shop: Replacement Handle Shaft for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Shop: etrailer Square Sidewind Trailer Jack - Drop Leg - 12-3/8" Lift - 10,000 lbs
- Shop: etrailer Square Trailer Jack - Side Pin Drop Leg - 12-1/4" Lift - 10,000 lbs
- Video: All You Need to Know About the Aluminum Sendel Series T17 Matte Black Mesh Trailer Wheel
- Video: An In-Depth Look at the Grease Seal
- Q&A: Determining The Correct Replacement Drop Leg Return Spring For 10,000lb Side Wind Trailer Jack
- Shop: Tonneau Cover
- Q&A: Replacement Spring for Bulldog Sidewind Jack with 12000-lbs Capacity
- Q&A: Replacing the Drop Leg Spring Loaded Pull Pin on a Bulldog 180 Series Square Jack
- Video: Review of etrailer Replacement Return Spring etrailer Ram Square Direct Weld Jack - TJD-12000-RSP
- Video: Review of the Gen-Y Anti-Rattle Clamp for 3" Hitch Receivers
- Video: A Closer Look at the Bulldog Round, A-Frame Jack Drop Leg and Pull Pin Assembly
- Video: Rebuilding a Bulldog 12000-lb Capacity Jack