Can SeeLeveL RV Holding Tank Monitoring System Be Installed on a Fiberglass Holding Tank

Question

Question:

Will the sensors work on a fiberglass holding tank? If not, can you recommend a sensor that does?

asked by: Mark S

1

Helpful Expert Reply:

Yes, the SeeLeveL RV Holding Tank Monitoring System # SE39VR will work with a fiberglass holding tank. If you check out the linked installation video you'll see one of our installers putting this on a fiberglass tank.

expert reply by: Jon G

1

Answer 1

Correct, the pump switch of the SeeLeveL RV Holding Tank Monitoring System #SE39VR provides an additional way to activate the water pump.

view full answer...

Answer 2

It is a 3-way switch. The SeeLeveL RV Holding Tank Monitoring System, #SE39VR includes a panel that incorporates readings for sensors to track 3 holding tanks, display of battery voltage and includes water pump switch. The integrated switch activates…

view full answer...

Answer 3

With your trailer not currently measuring propane levels, I would recommend going with the SeeLeveL RV Holding Tank Monitoring System #SE39VR which comes with the water pump switch. The reason for that is because the SeeLeveL RV Holding Tank…

view full answer...

Answer 4

While we don't carry any sensor system that would be able to communicate how many gallons are in your tank/how many were used we do offer the SeeLeveL RV Holding Tank Monitoring System #SE39VR, which has eight sensors for a more accurate reading.…

view full answer...

Answer 5

Yes, to get the SeeLeveL RV Holding Tank Monitor #SE34VR with the sensors you need the SeeLeveL RV Holding Tank Monitoring System #SE59VR. This comes with the same monitor along with 3 of the 12" long sensors you install on plastic tanks.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Leon! Your 23" bed depth is typical for newer Silverado 1500 trucks and will not cause a clearance issue. The Demco Autoslide #DM94AV has adjustable height settings of 15-1/4", 16-1/2", or 18" to help you achieve the…

view full answer...

Answer 12

Hey Jimmy! I would be happy to help you get setup to flat tow your 2024 Chevy Silverado 1500 Trail Boss. You will need a tow bar, base plate kit, safety cables, wiring, and a supplemental braking system. I recommend the following: -Roadmaster…

view full answer...

Can SeeLeveL RV Holding Tank Monitoring System Be Installed on a Fiberglass Holding Tank

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching