What is the Diameter of the Pollak 2-Pole Trailer Wiring Connector # PK12800

Question

Question:

What is diameter of the plug

asked by: Roger

1

Helpful Expert Reply:

In the attached picture I have indicated all of the different dimensions of the Pollak 2-Pole Trailer Wiring Connector, part # PK12800.

The diameter of the face of the connector where the two plugs are located is 1-1/2 inches.

expert reply by: Lori W

1

click to enlarge

Answer 1

That would be a great idea. We don't carry 4 gauge wire, but the #PK12801 2-pole connector would work great for what you are trying to do. For the male connector you would want the part #PK12800. The connectors are rated for up to 200 amps so you…

view full answer...

Answer 2

Hey Micah! Pacbrake has actually been around for a long time, more than 60 years. We have had customers ask for these air bags in the past, and we've seen them on vehicles coming in. Until now, Firestone has been the go to since their quality is…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 10

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 11

Hey Jeff, I checked with Firestone and the only version of the 2025 Toyota Tacoma that the part #F83VV doesn't fit is the 2 wheel drive models. The SR5 can be either 4wd or 2wd so you would need to verify which configuration you have to know if…

view full answer...

Answer 12

I recommend going with the Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs #AL89DQ for hauling around an in-bed camper with your 2024 Ford F-350 Super Duty. I really like this kit because it has the higher 7,500 lb rating (which you don't…

view full answer...

What is the Diameter of the Pollak 2-Pole Trailer Wiring Connector # PK12800

Product Page this Question was Asked From

Continue Researching