Will Curt Trailer Hitch Receiver 13394 Allow for Full Size Spare on 2018 Toyota Highlander
Published 04/06/2022 >
Products Featured in This Question
Question:
In the body of the response to my question you recommended use of the harness 5604. You had suggested use of a Draw Tite hitch in a previous paragraph. Does the 5604 wiring package go with the Curt 13394, if the car has existing tow package wiring?
asked by: Margaret W
Expert Reply:
The Curt Trailer Hitch Receiver # C13394 will fit with a full size spare tire stowed under vehicle unless the spare is on an aluminum rim, which is too wide. If you're concerned about the fit of the hitch with your spare tire I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver # DT84MR which doesn't have this restriction.
The Draw-Tite is also a Class III hitch with a 2" receiver. It has the same gross towing weight of 5,000 lbs and max tongue weight of 500 lbs. It also comes with an integrated mounting point for a 4-way or 7-way wiring connection.
If you need wiring, I recommend the Tekonsha T-One Vehicle Wiring Harness # 118449 if you don't have the factory tow package. This plugs into existing wiring, providing you with a 4-way to power a trailer's signal lights. If you do have the factory tow package you need the # 56042 instead.
If you're in need of a ball mount, check out the etrailer Ball Mount Kit # 989900. This kit has two ball mounts, one with a 3/4" rise or 2" drop and the other with a 2-3/4" rise or 4" drop. It also comes with a 1-7/8" and 2" ball, as well as a ball mount bag to store everything in.
I have attached some review and installation videos for your reference.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media




Continue Researching
- Search Results: electric tongue jack
- Search Results: rssa
- Shop: etrailer Trailer Brake Controller Installation Kit - 7-Way RV and 4-Way Flat - Detachable Harness
- Search Results: chill cube
- Search Results: backup camera
- Search Results: thule awning parts
- Search Results: thule roof rack feet
- Search Results: thule roof rack
- Shop: Replacement Printed Circuit Board for MaxxFan RV Vent
- Shop: Trailer Wiring
- Shop: Brake Controller
- Shop: Replacement Printed Circuit Board for MaxxAir Powered Lift RV Roof Vents w/ Exhaust Only Fan
- Shop: Stromberg Carlson Electric A-Frame Tongue Jack - 18" Lift - 2,500 lbs
- Shop: Mushroom Vent - White
- Shop: 7-Way RV Upgrade Kit for Trailer Brake Controller Installation - 12 Gauge Wires
- Q&A: Replacement Converter Section for PD4590K18NS2
- Shop: Replacement Dome for Ventline E-Z Lift Ventadome Trailer Roof Vent - White
- Shop: Base Plate for Tow Bar
- Shop: RV Camera
- Shop: Roof Rack
- Q&A: Replacement 10-21275KE Circuit Board for MaxxAir Vent Fan
- Shop: Trailer Hitch
- Video: Installing the Curt Trailer Hitch Receiver on your 2014 Toyota Highlander
- Shop: BOLT brand vehicle and hitch locks
- Video: Best 2014 Toyota Highlander Trailer Hitch Options
- Q&A: Will Adding the Tow Package to a 2015 Toyota Highlander Increase Towing Capacity
- Video: Setting up the Curt Trailer Hitch Receiver on a 2015 Toyota Highlander
- Q&A: Comparing Trailer Hitches for 2019 Toyota Highlander
- Q&A: Panel Trimming Required For The Curt Receiver # C13394 Installation on a 2017 Toyota Highlander
- Q&A: What to Do If My Hitch Bolt Holes Dont Line Up


Margaret W.
4/6/2022
In the body of the response to my question you recommended use of the harness 5604. You had suggested use of a Draw Tite hitch in a previous paragraph. Does the 5604 wiring package go with the Curt 13394, if the car has existing tow package wiring?