Can etrailer Axle # e94YR Travel 65-70 MPH

Question

Question:

How are you? I have a couple questions about your axle e94YR. This question actually pertains to the 2000 pound axle as well... are these rated for speeds of 65 or 70 miles per hour? My next question is is it possible for you guys to do them in a Spring over variation instead of Spring under or are the perches already welded on when you get them? Thanks in advance

asked by: Christopher S

0

Expert Reply:

Yes, the Trailer Axle with Idler Hubs # e94YR is rated to easily go 60 to 70 mph. It's typically the tire that is what limits the speed rating and not the hub or axle. We do not have a spring over variation like you mentioned.

expert reply by: Jameson C

0

Answer 1

The etrailer Trailer Axle with Idler Hubs #e84YR is different than the 2,000lb Dexter 6047 axle. This axle is closer to the Dexter #T20BTR-6048 with the 48" spring center to spring center measurement. Both have 60" hub faces with a…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Not another one! Just kidding Dirk! I was in the Marines I enjoy these conversion questions on the M1101 trailers. I'd be more than happy to list the parts you need, along with quantity, and confirm compatibility. 1 - Timbren Axle-Less Trailer…

view full answer...

Can etrailer Axle # e94YR Travel 65-70 MPH

Product Page this Question was Asked From

Continue Researching