Can 24x40 etrailer Cargo Carrier for RV Bumper e99050 fit 1/2 inch Clearance for Bumper

Question

Question:

My trailer bumper is 4.5inch x 4.5inch with 0.5inch gap between the trailer and the bumper ..... will your clamps fit this configuration? Thx in advance for your reponse.

asked by: Mitch N

0

Expert Reply:

If the bumper of your trailer sits lower than the bottom of the trailer body then yes the 24x40 etrailer Cargo Carrier for RV Bumper # e99050 would fit and work well. If the bumper sits up higher though it would not fit as the hardware that secures the carrier to the bumper would interfere.

expert reply by: Jameson C

0

Answer 1

If you have a 12 volt system on your camper, you will need to wire your 6 volt batteries (in series), like the attached drawing shows. You would need to run a jumper from the positive side of one battery to the negative side of the other battery.…

view full answer...

Answer 2

Since you have a recessed bumper on your Keystone Outback, instead of using the 24x60 etrailer Cargo Carrier for RV Bumper #e99049 I recommend going with the: -24x40 etrailer Cargo Carrier for RV Bumper #e99050. This cargo carrier will work better…

view full answer...

Answer 3

All other things being equal, yes, it is better to use a weight distribution head assembly and shank from the same manufacturer. This allows you to know with certainty what the weight capacity of such a set-up actually is. If parts from different…

view full answer...

Answer 4

The Curt Hitch Adapter #C45405 will not reduce the tongue weight of your hitch. Many adapters that extend the length will reduce towing capacity based on tongue weight, but this adapter isn't one of them. It will work fine with the Curt TruTrack…

view full answer...

Answer 5

Due to the bumper being partially recessed under the RV, you wouldn't be able to attach the #e99050 cargo carrier as you wouldn't be able to slip the mounting brackets onto the bumper from above. This being said, we do offer a solution that…

view full answer...

Answer 6

The 24x84 etrailer Cargo Carrier for RV Bumper part #e96ZR can hold a spare tire but there isn't any sort of specific mount for this. The photo attached below is a custom job from a neighbor and I'm not totally sure what they used to create…

view full answer...

Answer 7

Hello Bernie, thanks for getting in touch. The 24x60 etrailer Cargo Carrier for RV Bumper #e99049 includes the carrier itself, the supports, bumper brackets and all necessary hardware. You can see all of the included parts in the pictures below.…

view full answer...

Answer 8

I do have a possible solution for you but unfortunately there aren't any battery boxes available that will hold two 12V batteries and fit within a 21" length and 8" width. The closest thing we have is the TorkLift PowerArmor Locking…

view full answer...

Answer 9

Hi Bob; the inside dimensions of the #e82FV are going to match up to the cargo carrier you install it on. Since this is designed for 24" x 60" cargo carriers that will be the inside width and depth once it is tightened down on the carrier.…

view full answer...

Answer 10

Hello David, The reason it’s $1000 more is because of the whopping 0.2 cu. ft. of extra space..... just kidding! The main difference comes down to the exterior and features. The #GE48FR has a sleek glass front that gives it a glossy, modern look,…

view full answer...

Answer 11

Hello Mark, Happy to help you find the right weight distribution hitch to meet your needs. I don’t have a database that supplies specs for trailers (though it would be pretty sweet if one existed), so based on my research, the Rockwood Mini Lite…

view full answer...

Can 24x40 etrailer Cargo Carrier for RV Bumper e99050 fit 1/2 inch Clearance for Bumper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching