Class IV Hitch that Fits 2006 Ford E-450 Cab and Chassis

Question

Question:

I have a Ford E450 cab and chassis with a Wheeled Coach ERV conversion. Im looking for a hitch that will fit it.

asked by: James C

0

Expert Reply:

We have a Class IV hitch that fits your 2006 Ford E-450 with the Draw Tite part # 41947 but the # 14090 would not fit.

expert reply by: Jameson C

0

Answer 1

I do have an option for you though there aren't custom fit hitches for box trucks. The frame is not really the issue but rather the body the up-fitter adds on which could hang down below the frame where the hitch mounts or actually use the holes…

view full answer...

Answer 2

For your 2006 Ford F-450 Shuttle Bus you are going to need to use a universal hitch. For this you will need to measure how wide your frame rails are apart on the rear of your bus. Then you will need to know how much drop from the frame rails to the…

view full answer...

Answer 3

It sounds like you have an older generation of the Carlisle Hydrastar brake actuatuator. The current #HBA-CAM would only be compatible with 6th generation and newer actuators. It wouldn't be a compatible replacement for your 381-7061. The current…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Hey Sean, yes you can definitely use a stand alone system like a single-acting hydraulic pump to power a hydraulic trailer jack like the single action Stillwell lineup we just started carrying. For the Stillwell Atlas IV 10K Hydraulic Trailer Jack w/…

view full answer...

Class IV Hitch that Fits 2006 Ford E-450 Cab and Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching