Replacement Lid & Operator Mechanism For MaxxFan Plus 4500K Roof Vent

Question

Question:

Thanks Kyle The lift arm looks tweaked also on 1side. Could that b why it will not fully engage In open position? I will order the operator part u suggested if u think that is the issue instead. Do u have a suggestion for the seized set screw to remove fan blade to access parts to replace? Thanks

asked by: Joy W

0

Expert Reply:

Let's go ahead and start with the lift mechanism, which is also called the operator mechanism for your MaxxFan Plus Roof Vent # MA00-04500K, which is faulty and why your fan won't stay open. For that we do offer the replacement:

- Replacement Operator Mechanism # MA10-20281K-1AF

In regards to the replacement lid in Smoke for your MaxxFan Plus vent, we do have that part, which is the following:

- Replacement Lid for MaxxFan and MaxxFan Plus Roof Vents - Smoke # MA10A40009K

expert reply by: Kyle S

0

Joe W.

4/29/2021

Thanks Kyle The lift arm looks tweaked also on 1side. Could that b why it will not fully engage In open position? I will order the operator part u suggested if u think that is the issue instead. Do u have a suggestion for the seized set screw to remove fan blade to access parts to replace? Thanks

Kyle S.

4/29/2021

If the lift arm itself looks "tweaked" or somehow damaged, then I do recommend replacing that as well: - Replacement Lift Arm for MaxxFan Roof Vents # MA10-20222KS As for the seized screw, there really isn't much we can offer there other than home remedies like holding a screwdriver in place and trying to turn it slowly while hitting the back of the screwdriver with a hammer to create sort of an impact wrench.

Answer 1

If you need hardware to install the MaxxFan Plus Roof Vent part #MA00-04500K I recommend using the Roof Vent Installation Kit part #344270KITW for white or part #344270KITB for beige. These kits come with all the screws, butyl tape, and sealant you…

view full answer...

Answer 2

I was able to confirm that the Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - White #V2092SP-28 you were looking at is white in color. The #V2094SP-28 has a white lid, but uses a birch white trim which is an off white…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Lid & Operator Mechanism For MaxxFan Plus 4500K Roof Vent

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching