Radio Replacement for Jensen VR185 In Cab Stereo

Question

Question:

i am looking for a replacement radio for my jensen VR 185 which is in my 2007 fleetwood excursion. do you have anything that is compatable with this replacement. the space in the dash is limited so there can not be a lot of cutting to make a new system fit.

asked by: Christopher D

0

Expert Reply:

I do not have an exact replacement - but I have something similar.

Your Jensen VR125 stereo measured 3-1/2" tall by 7" inches wide.
The Jensen # JWM45 stereo measures 3-3/8" tall by 8-3/16" wide.

The odd sizing of your radio makes it difficult to find a replacement solution.

expert reply by: Les D

0

Answer 1

Hey, Ted. Thanks for your question. Since you’re already running the Voyager monitor #VOM719WP, the Voyager Rear Camera #VCMS17B will be exactly what you need. This camera includes a 36" lead, so you will most likely need an extension cable to…

view full answer...

Answer 2

I spoke with my contact at Jensen regarding your VR185 stereo that you have installed in your Fleetwood Motorhome. She stated that they do not currently have a replacement stereo available that requires the same 3.7 inch tall x 7.2 inch wide cutout…

view full answer...

Answer 3

I reached out to the manufacturer regarding your question. Their response goes as follows. The VR185 was an in dash radio and the JWM60A is a wall mount radio for the living space of the RV. It is very big and would not fit where the VR185 is. To…

view full answer...

Answer 4

Hi Peter; the Voyager RV Backup Camera Monitor #VOM719WP comes with everything you need. Unfortunately, Voyager does not offer an adapter or version with that plug so you will have to splice in the wires for installation.

view full answer...

Answer 5

So long as you are okay with splicing, then Voyager has told us that you can replace your AOM7694 with the Voyager RV Backup Camera Monitor - 7" Screen - 4 Video Inputs #VOM719WP. The wires on the #VOM719WP are labeled, so I recommend making a…

view full answer...

Answer 6

Actually the type of roof vent cover you need to attach to the vent cover brackets of your Maxxair 4951KS like part #MA00-04500K is the part #MA00-955003 which uses those brackets with the included cotter pins of the cover.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Radio Replacement for Jensen VR185 In Cab Stereo

Continue Researching