Installation and Torque of 1-1/4 Inch Shank Hitch Ball onto Ball Mount

Question

Question:

Recommended torque settings for 1 1/4 ball mount are 450ft/lbs! I seem to have misplaced my 450ft/lb torque wrench. What types of businesses would typically be able to do this for me?

asked by: Jason

0

Expert Reply:

That foot pound rating for torqueing a hitch ball onto a ball mount requires a special torque wrench. A local mechanic should have something compatible. If you can't find anyone with the correct torque wrench as many max out at 250 lbs, then we recommend using a breaker bar and pipe extension to at least ensure the lock washer is completely compressed to flat before use. Installing the ball mount sideways in the receiver tube will allow the best hold (although without pin obviously) for keeping the ball mount in place while applying the downward pressure with the breaker bar socket wrench and extension.

Obviously we recommend getting the manufacturers specs for torque using the proper torque wrench.

expert reply by: Jason S

0

Answer 1

For storage of RV with a water filter system such as the Clearsource Ultra RV Water Filter System, #CS87FR, you should consider removing the filters from the canisters and blowing out the system with pressurized air using the Valterra RV Blow Out…

view full answer...

Answer 2

I did some checking on the AquaFresh Exterior RV Water Filter Kit part #A01-1131VP and the micro rating is 20. The water filter kit reduces chlorine, sediment, and bacterial all while improving the taste and odor of your fresh water supply. The…

view full answer...

Answer 3

Bulletproof Hitch products, including the #358smallshackle used to be made here in the United States. In Bradenton, Florida I believe. Recently though they have moved production overseas.

view full answer...

Answer 4

In order to install a 7-way trailer connector on a 2017 Kia Sedona you will need to start with a 4-way and for this I recommend the Curt T-Connector Vehicle Wiring Harness part #C56332 which is plug-n-play. Then, you can add the 4 to 7-way adapter…

view full answer...

Answer 5

Hey Grant, did you test all of the tires that run to your stoplight circuit with your tester? If not, that is the place to check. Since you used a non contact tester and some say those aren't always reliable I would try again with a probing…

view full answer...

Answer 6

I have a solution for you because as you know what you have now cannot charge Lithium batteries. You will need the Progressive Dynamics #PD4135K which is designed to replace your WF-8735P and is compatible with Lithium batteries. When this is…

view full answer...

Answer 7

It sounds like you have a pretty good idea of what you need. You will need a 7-way connector as well as a brake controller. You'll first need to choose a brake controller. The option with the easiest installation would be the Curt #C51180 Echo…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will need to start with a 4-way (if you do not have one) on your 2018 Kia Sedona. For that you would want the #C56332. From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want…

view full answer...

Answer 10

I do have an option for you but the Derale 25-Row High-Performance Stacked-Plate Cooler part #D52506 would be a bit overkill for your 2017 Kia Sedona nor do I think you would have the space to install this. Instead, I recommend the Derale Series 8000…

view full answer...

Answer 11

The red wire on the trailer brake controller that goes to the cold side of the stop light switch is a power wire, and should not be grounding. This wire gives 12 volts of power only when the brake pedal is switched, and is what tells the controller…

view full answer...

Answer 12

I can certainly point you in the right direction. Unfortunately I cannot tell you exactly what color wire to connect to, as these wire colors are not always universal. I recommend going in with a wire tester like the #PTW2993. You will need to probe…

view full answer...

Installation and Torque of 1-1/4 Inch Shank Hitch Ball onto Ball Mount

Product Page this Question was Asked From

Continue Researching