Compatible Door Stop for my JR Products Door Slider

Question

Question:

does the JR Products screen door stop part number 37211135 work with jr products door slider part number 37211195, the video does not show it.

asked by: Victor K

0

Expert Reply:

The JR Products Screen Door Slider part # 37211195 is compatible with the JR Products RV Screen Door Stop part # 37211135 designed for use with 12" Sliders.

expert reply by: Randy B

0

Answer 1

The 1/8" thick tape is most common for side window installation and repairs so I recommend the Alpha Systems Butyl Tape for RV Weatherproofing part #AL42FJ for this. It can always be doubled up if needed. I recommend the 3/16" thick tape…

view full answer...

Answer 2

It sounds like you're looking for the ceiling garnish for a standard roof vent like #VA0445-34. I've linked our selection for you. Just choose the color and the measurement of the leg you need. The leg is essentially how tall the garnish is.…

view full answer...

Answer 3

Hey Mary! You aren't going to like this answer, but Atwood went out of business a number of years ago, so the only way you're going to find replacement parts is from someone that has a used one they're wanting to piece out. What…

view full answer...

Answer 4

I reached out to the manufacturer, JR Products, who told me the distance was 9.7" (about 9-11/16") apart between the two farthest mounting holes, and 4.85 inches (about 4-7/8") apart to the closest mounting holes. They do come in your…

view full answer...

Answer 5

The best way to select the correct size vinyl trim insert is to measure the trim insert you have now while flat, not the track. We don't really recommend measuring the track as they are not all a standard width. That said, we only offer vinyl…

view full answer...

Answer 6

If your vent uses a smaller opening that what the #V2111-03 that you referenced is designed to fit (10-1/2" wide x 3-3/4" tall rough opening), then you could remove the collar from the #V211-03 so that the back of it would sit flush with…

view full answer...

Answer 7

Hello Eric, Welcome to etrailer, I'm glad you found us! You can definitely make that upgrade, and I think you'll be much happier with the Furrion Chill Cube. The variable speed compressor is designed to adjust its output based on the cooling…

view full answer...

Answer 8

Hey Dave. The T5079 RV Designer Entrance Door Lock item #RD68SR is made of a die-cast zinc alloy for the housing and handles. The strike plate, plunger load pins and plunger end plates are made of steel. The parts are then black powder coated and…

view full answer...

Answer 9

Hi Olin; since yours is 12" x 12" the Lippert Motor Home Entry Screen Door Bubble Slider Panel #LC234101 is the correct replacement. The older models had the more rounded bubble. This is just the slider panel. I'm not 100% sure what you…

view full answer...

Answer 10

Hey Steve! The brake light relay is related to braking systems like the Patriot #BLU37TR. It is not required for the installation of the EZ Light Wiring Harness #BX88285. It also isn't required at all for a 2014 Wrangler Unlimited. However, you…

view full answer...

Answer 11

The Lippert Motor Home Entry Screen Door Bubble Slider Panel - Frosted #LC234101 measures to your required size at 12 x 12-inches. This part is clear, and it can be trimmed is necessary.

view full answer...

Answer 12

You'd want to install the disconnect on the positive leg, if you grounded the negative leg and the circuit was accidentally grounded, damage could occur. Interrupting the positive leg would prevent this from happening. We recommend installing the…

view full answer...

Compatible Door Stop for my JR Products Door Slider

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching