Remote Compatible with MaxxFan Plus 00-04900kx

Question

Question:

I purchased the MA99FR MaxxFan Plus 12 V 10 speed . Which remote works on this fan? Thank you,

asked by: Lisa

0

Expert Reply:

The Replacement Roof Vent for MaxxFan Plus Roof Vent w/ 12V Fan - Powered Lift - 10 Speed - Smoke # MA99FR you referenced will use the Replacement Wall Control Panel for MaxxAir MaxxFan Plus Roof Vent # MA59FR. This is a wired remote that mounts to the wall. There isn't a wireless remote control unit for that specific vent fan.

expert reply by: Jason S

0

Answer 1

The Replacement MaxxFan Plus 10-Speed Roof Vent with Smoke Lid #MA99FR is only compatible with the wall mount/remote (it says wall mount but can be used as a remote as well) Replacement Wall Control Panel for MaxxAir MaxxFan Plus Roof Vent #MA59FR.…

view full answer...

Answer 2

Based on the part number of your motor the correct circuit board would be the part #MA10A21275K.

view full answer...

Answer 3

Hi T.J.; thank you for providing that information and the picture. The correct replacement circuit board for your MaxxFan is the #MA10A04751KS which is the same as the 10C04751KS you referenced.

view full answer...

Answer 4

We have the Replacement Hardware and Backer Plate #LC702580 you need for your SolidStep Manual Fold-Down Steps #LC791573. We also have the SolidStep Locking RV Storage Box #LC664640 that will replace folding steps and give you additional storage…

view full answer...

Answer 5

Hey Mike, thanks for reaching out! The Replacement Printed Circuit Board for MaxxAir Powered Lift RV Roof Vents w/ Reversible Fan #MA10A21275K is the newer "10C21275K" C version you're wanting to get. Our part numbers don't always…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Remote Compatible with MaxxFan Plus 00-04900kx

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching