Solution to Allow 2015 Toyota Tundra to Tow Trailer and Carry Motorcycle Carrier

Question

Question:

I have a 2000 BAMBI RV which is 19ft long, 3600lb Dry Wt., 500lb Hitch Wt., 4500lb GVWR Hitch Ball Ht. I also have a 300lb dual sport motorcycle I would like to bring on my trips. My tow vehicle is a 2015 Toyota Tundra with a 2inch receiver. Im wondering if there is a dual hitch setup can be used to tow both my RV and motorcycle using a motorcycle carrier? Would this D210 dual hitch receiver work? Thanks in advance.

asked by: Don F

0

Expert Reply:

I think I might have a solution you'd like but there isn't a dual hitch adapter that's going to have the capacity needed for the weight of your bike and carrier plus the tongue weight of your trailer. What you could do is install a front hitch on your 2015 Toyota Tundra with the Draw Tite part # 65080 and then use a motorcycle carrier like part # E98873 and you'd be able to still tow your trailer.

Since that would be quite a bit of weight on the front suspension I'd also recommend the Coil SumoSpring part # CSS-1069F to help provide more support up front and you'd be set!

expert reply by: Jameson C

0

Answer 1

I had our warehouse measure each of the front mount trailer hitch receivers you mentioned, and the dimensions are as follows. The Curt #31408 measures 32-3/4" long x 8-3/4" wide, the Draw-Tite #65080 measures 36-3/4" long x…

view full answer...

Answer 2

I was able to get the measurements you were looking for of the Draw-Tite front mount hitch that fits your 2020 Toyota Tundra, which is the following: - Draw-Tite Front Mount Trailer Hitch Receiver #65080 The hitch is similar to the Curt #31198 in…

view full answer...

Answer 3

There is no reason why you couldn't install a front mount hitch and and add a front load bar to help support your Kayak and create more clearance between it and your travel trailer. The front mount hitch I recommend for your 2007 Toyota Sequoia…

view full answer...

Answer 4

The Curt #33055 you mentioned isn't a fit for the 1991 F-250, it's a fit for the E-Series Vans, which Curt confirms. Unfortunately, they don't offer a front mounted hitch for your truck. The bolt hole spacing I was able to obtain is as…

view full answer...

Answer 5

Whether the Ford E-450 van chassis is a 2002, 2003, or 2004 (or anything in the 200 to 2007 model year range) it will take front mount receiver #65001. So no worries, we got you covered! The Curt hitch, #33055, is indicated as a fit for the E-350 but…

view full answer...

Answer 6

The B&W Heavy-Duty Trailer Hitch, part #BWHDRH25122 is designed to fit a 1995 GMC C/K Cab And Chassis pickup. This hitch will fit pickups with a 34 inch frame and will not work on trucks that have dual fuel tanks. I pulled one of these from our…

view full answer...

Answer 7

No, there are not. The aftermarket hitches, like the etrailer item #e55KR, all mount below the original location of the factory hitch on your 2005 Ford Explorer XLT. I have attached a picture below to show you what it will look like once installed. I…

view full answer...

Answer 8

The length from the inside of one mounting bracket to the other is 27" on the Curt Front Mount Trailer Hitch Receiver #31540. Distance from mounting holes center to center is 30" and the mounting plate thickness is 5/16". Refer to the…

view full answer...

Answer 9

The Curt Front Mount Trailer Hitch Receiver #33055 that you referenced fits Ford Vans (up to an E-350), but since your Chateau is on a 2000 Ford E-450 you would need to go with the Draw-Tite #65001. Installation instructions and a photo showing the…

view full answer...

Answer 10

There is not any added hardware required to install the Curt hitch that fits your 2022 Ford Ranger, which is the following part number: - Curt Trailer Hitch Receiver #C13417 Installation of the #C13417 on a '22 Ranger just requires removing the…

view full answer...

Answer 11

The #BWHDRH25122 has 35-5/8 inches between mounting holes like what you see in the picture I attached. Since you need larger than than let me know what vehicle you have and I can see which would be best fit.

view full answer...

Answer 12

The B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25122 that will fit your 1986 Chevy K20 will measure 5.438" from the top of the frame brackets to the top of the receiver. If this is looking like it will not be enough to clear the bottom of…

view full answer...