Rear Torklift Camper Tie Down for 2008 Chevy Silverado 3500 with Torklift SuperHitch

Question

Question:

I purchased and installed a TLC1205 dual receiver hitch on my 2008 Chevy Silverado 3500. What is the part number for the rear tie downs to fit hitch

asked by: Joe S

0

Expert Reply:

The correct rear Torklift tie downs you need for your 2008 Chevy Silverado 3500 are the part # TLR3503 since you have the Torklift hitch # TLC1205.

expert reply by: Jameson C

0

Answer 1

The TorkLift SuperHitch Magnum Trailer Hitch #TLC1205-30 that you referenced has been confirmed as a fit for your vehicle so it would be a great choice as it has a ton of capacity like you said you needed. Maximum gross trailer weight: 20,000 lb…

view full answer...

Answer 2

Yes, the Torklift Class V hitch part #TLC1205 would be a great option for your 2002 Chevy Silverado 2500HD long bed. If you instead had a short bed truck you would want the part #TLC1204. The 17k capacity is more than what your truck is rated for so…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Hello Mike, Sounds like you are getting things set up the right way and not going over your payload, I respect that. It looks like the weights are the same whether you have a 6 3/4' or 8' bed. If you happen to have an aftermarket hitch,…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Rear Torklift Camper Tie Down for 2008 Chevy Silverado 3500 with Torklift SuperHitch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching