How Wide is Ramp Hook of Gen-Y Hitch Aluminum Loading Ramp Set

Question

Question:

I am wondering what is the width between the ramp itself and the hook that goes over the rail of the trailer. I am looking for a ramp that could possibly fit over an inch and a half round bar stock.. Thanks

asked by: Corey M

0

Expert Reply:

The hook opening of the Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R72 is two inches wide. I attached a picture that shows where the measurement is taken.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The thickness is 2-3/4 inches for the Gen-Y Hitch Aluminum Loading Ramp Set - 72" Long x 14" Wide #325-GH-R72.

view full answer...

Answer 2

I went out to the warehouse and took a look at the Gen-Y Hitch Aluminum Loading Ramp Set item #325-GH-R72. I have linked a picture below that will show you what the bottom end of this ramp looks like. This ramp set is 72" long x 14" wide…

view full answer...

Answer 3

The height restriction on ramp set #288-07502 has to do with the distribution of the weight, ability for tires to grip, and clearance between the tops of the ramps and the vehicle rolling up them. The shorter the ramp the more severe the angle will…

view full answer...

Answer 4

I do have a few easier options for you to determine the weight capacity of an axle other than using the bolt pattern or the number of lug nuts. The problem with using the bolt pattern to tell the axle capacity is that an axle may have the a bolt…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hello Ben, Thanks for writing in! Yes! The WeatherTech Front Auto Floor Mats #WT54TZ you were looking at are made specifically for the factory vinyl floor in your 2026 Ram 2500. For the rear, WeatherTech does not have a matching custom-fit rear mat…

view full answer...

Answer 7

Hey, Mike. That's a really good question. I'd like to get some pictures of your trailer so I can get a visual of what yours looks like in the back. If you could reply to the email with pictures I'll be able to go from there! I want to…

view full answer...

Answer 8

The Gen-Y 72" Ramps #325-GH-R72 do have hooks on the end to help make connection to the trailer easier and more stable, but there isn't an additional plate that can be added to a trailer specifically for this application. With that said, you…

view full answer...

Answer 9

Happy to help Joe, thanks for reaching out! From what you're looking to get out of a trailer jack, I'd suggest the Dutton-Lainson Boat Trailer Jack w/ Wheel #D22335. It has a large 8" x 3-5/16" single wheel, 1,500-lb capacity, their…

view full answer...

Answer 10

Hey Gary, thanks for the information! The etrailer Horizontal E Track item #e85VR would be a great way to add additional anchor points. You can bolt these tracks directly to your trailer's deck using self-drilling metal screws like item #SL99FR.…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

The Stallion #288-07432-2 folding cargo ramps are manufactured in China. If you'd prefer a US made alternative, I'd recommend the Gen-Y #325-GH-R84 84 inch long aluminum loading ramps. If you click the provided link, you can see a product…

view full answer...

How Wide is Ramp Hook of Gen-Y Hitch Aluminum Loading Ramp Set

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching