Dimensions Of Curt Weight Distribution Shank C17132
Updated 05/18/2020 | Published 07/20/2019
Question:
I have a 2018 ram 2500 with the Reese steady flex system, I have pulled my camper with the 2” reducing sleeve and I’m not thrilled with the slop in the hitch. I would like to know the measurement from the pin hole to the front of the shank on the curt c17132 so I can make sure I can open my tailgate with the trailer hooked up.
asked by: Jake S
Expert Reply:
I went to the warehouse and measured the Curt Weight Distribution Shank for 2-1/2" Hitches # C17132 and it measures 9" from the center of the hitch pin hole to the end of the vertical portion of the shank. I have attached a diagram with some other measurements I took as well that may be helpful.
Product Page this Question was Asked From
Curt Weight Distribution Shank for 2.5" Hitches - 9-1/4" or 10" Drop - 13" Rise
- Accessories and Parts
- Weight Distribution Hitch
- Shanks
- 1400 lbs TW
- Fits 2-1/2 Inch Hitch
- Round - 10 Inch Drop
- Trunnion - 9 Inch Drop
- Round - 13 Inch Rise
- Trunnion - 13 Inch Rise
- CURT
more information >
Continue Researching
- Shop: Curt Weight Distribution Shank for 2.5" Hitches - 9-1/4" or 10" Drop - 13" Rise
- Q&A: Looking For Extended Weight Distribution Shank To Solve Tailgate Clearance Problem
- Shop: Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 10" Rise/6" Drop
- Search Results: spare tire mount
- Q&A: Will Standard B&W Continuum Shank Allow Tailgate To Open On 2026 Ford F-250 King Ranch
- Shop: Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 7" Rise, 3" Drop
- Q&A: Upgrading to 2-1/2 Inch Shank or Using a Reducer Sleeve with Equal-I-zer Weight Distribution System
- Shop: Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 16" Long - 7" Rise, 3" Drop
- Video: What to Know About the Curt Weight Distribution Shank for 2.5" Hitches
- Shop: Curt Weight Distribution Shank for 2" Hitches - 3-1/8" Drop - 7-1/8" Rise
- Shop: Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 8" Rise, 4" Drop
- Q&A: Can You Convert to 2-1/2 Inch Shank From 2 Inch With Reese Weight Distribution Hitch
- Q&A: Will the Curt 2-1/2 Inch Weight Distribution Shank Work With 2 Inch Weight Distribution Head
- Q&A: Shank For Fastway e2 Weight Distribution That Fits 2-1/2 Inch Hitch Receiver
- Shop: Equal-i-zer Weight Distribution Shank - 12" Long - 13" Rise, 9" Drop
- Video: All You Need to Know About the Lippert Spare Tire Winch with Offset Cable
- Q&A: Best Weight Distribution Shank for a 2018 Ram 2500
- Video: Shocker Hitch HD Air Ball Mounts | Manufacturer Interview
- Search Results: 2 1 2 weight distribution shank
- Search Results: valley weight distribution hitch
- Search Results: 2 inch shank
- Search Results: 2 1/2 inch shank
- Video: Breaking Down the Camco RV Awning Anchor Kit w/ Pull Tension Straps
- Video: Hands-On with the Equal-i-zer Wt Distribution Shank
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Search Results: weight distribution shanks
- Video: The Low-Down on the Equal-i-zer Weight Distribution Shank
- Search Results: bullet proof
- Video: Set up: Equal-i-zer Weight Dist Shank on a 2013 Ford F-250 and F-350 Super Duty
Gary A.
5/11/2020
I need a weight distribution shank for a 2.5 inch receiver. I need the total length of the shank to be 16'' from top of the receiver to bottom of the drop. I am using a blue ox sway pro. The curt c17132 does not give me quite enough drop and the curt c17125 drops too much. Does curt, or anybody else make a shank in between these 2? Thank you much.