Replacement Kit for Plug Clip for BrakeBuddy Stealth

Question

Question:

I have a BrakeBuddy Stealth system and the clip on the front plug in that is installed on the front of my tow vehicle needs to be replaced. Appears the spring mechanism broke Where can I get replacement parts for the BrakeBuddy Stealth system?

asked by: Jeremy A

0

Expert Reply:

I spoke with my contact at Hopkins and he told me that you'd need the Hopkins Stealth Connector Kit # HM39531 is what you need to replace the parts you mentioned on your Hopkins BrakeBuddy # HM39530.

expert reply by: Jameson C

0

Answer 1

Currently the only replacement parts we have for the Brake Buddy Stealth Supplemental Braking System #HM39530 are as follows. Replacement Flex-Coil Adapter #HM39532 Replacement All in 1 Connector Socket #HM39531 Replacement Dual Controller #HM39533…

view full answer...

Answer 2

As long as the in-cab controller of the Brake Buddy Stealth Supplemental Braking System #HM39530 has power the mode indicator light will remain on. The power draw of this light is so low that it would take a considerable amount of time for it to…

view full answer...

Answer 3

It sounds like you're looking for the Replacement Flex-Coil Adapter #HM39532 which plugs into the brake buddy stealth #HM39530 and then goes to your tow vehicle.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Replacement Kit for Plug Clip for BrakeBuddy Stealth

Continue Researching