Can the Race Ramps Wheel Cribs be Painted or Powder Coated
Published 11/30/2018
Products Featured in This Question
Question:
my only other question would be would the paint what kind cover the label sign on the wheel crib Also would the design of the race ramps on top where the wheel sets look different from the one that is made for the bottom and the one that goes on the top if you stacked it The reason i ask is that if i use for a display for my car at a car show would all 4 pieces look the same Thanks
asked by: Gene
Helpful Expert Reply:
The Race Ramps Adjustable Height Wheel Cribs part # RR-WC-12-2 that you referenced could be painted to your liking but the heat from the powder coating process would ruin them so I cannot recommend this. If you were to split each wheel crib and put one of the cribs under each of your wheels then the vehicle would look the same from each side in regards to distance from the ground.
Product Page this Question was Asked From
Race Ramps Stackable Wheel Cribs for Service and Display - 12" Lift - 15-1/2" Long - Qty 2
- Car Ramps
- Storage and Display Ramps
- Display Ramps
- 12 Inch Lift
- 3000 lbs
- 12 Inch Wide
- 15 Inch Long
- Foam
- Race Ramps
more information >
Continue Researching
- Q&A: Can Swagman XTC-2 TILT # S64671 Carry Womens Bike Frame
- Video: Swagman XC 2 Bike Rack Test Course
- Video: Beginner’s Guide to Installing the etrailer Trailer Hitch Receiver on a 2017 Chevrolet Equinox
- Search Results: hitch bike racks
- Shop: Trailer Hitch
- Video: Clean Up Your Trailer Wiring
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: Clearance Differences Between Hitches For A 2026 Honda Odyssey EX-L
- Search Results: trailer tires and wheels
- Video: Curt Powered Tail Light Converter Installation - 2023 Kia Telluride
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Brake Controller
- Article: How to Measure for Trailer Hitch Drop
- Video: Installing the Curt Trailer Hitch Receiver on a 2025 Toyota RAV4
- Q&A: Comparing the Curt Hitch C13416 and EcoHitch Hitch 306-X7396 for a 2019 Toyota RAV4
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: trailer hitch ball mount
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Base Plate for Tow Bar
on Car Ramps
Gene
11/30/2018
my only other question would be would the paint what kind cover the label sign on the wheel crib Also would the design of the race ramps on top where the wheel sets look different from the one that is made for the bottom and the one that goes on the top if you stacked it The reason i ask is that if i use for a display for my car at a car show would all 4 pieces look the same Thanks