Does Equalizer for 2" Wide Slipper Springs # E4541-Z Require Bushing for 7/8 inch Bolt

Question

Question:

I am ordering these to replace worn units and 7/8 wet bolts. Is there a bushing for the 7/8 center bolt as well? Thanks

asked by: Rick R

0

Expert Reply:

The center hole of the # E4541-Z that you referenced has a metal bushing and is 7/8 inches in diameter. Because of that you would not need an additional bushing to run a 7/8 in diameter bolt.

expert reply by: Jameson C

0

click to enlarge

Answer 1

It really depends on the springs used. Take a look at the picture I have included that shows hanger spacing based on several different springs. This will be a good guide to reference when mocking up the suspension on your trailer. This is also found…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey JT! Sorry to hear about your trouble with the leaf springs. Hopefully there wasn't a lot of damage and everyone stayed safe. From what I have found the 26E-3500 is the same as the Dexter 072-027-00. This is the 6-Leaf Double-Eye Spring for…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Hey Richard, great question. To get the full 2-1/4" lift on a tandem axle setup, you actually need the triple axle kit part #RR55QX instead of the #RR23QX tandem axle kit. You could also achieve this by getting the tandem axle kit, and an…

view full answer...

Answer 6

Hey Greg, yes the Aluminum Hi-Spec Series 04 Star Mag Trailer Wheel #AM20258 that you referenced would work with a Load Range E tire ST175/80R13 like you mentioned.

view full answer...

Answer 7

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

There is no exact way to determine the leaf spring length. The best way to determine the length for a replacement is by measuring the existing leaf springs. The hanger distance and shackle length can help you get a good idea, but you're looking…

view full answer...

Answer 10

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 11

The determine the correct replacement leaf spring on your 2021 Coachmen 259FKDS you'll need to lift your trailer frame so the spring is hanging freely and then measure from center-eye to center-eye, then for the equalizer you need to measure…

view full answer...

Answer 12

Thanks for the pictures! Based on the weight of your 2008 Keystone Cougar 5th Wheel, you will want the item #LG-1 landing gear set. You are going to want to measure to be sure this is the right size for you. The two things you will want to measure…

view full answer...