Why Doesn't the Lippert Scissor Stabilizer Jacks # LC285344 Lower Itself From Weight of Trailer

Question

Question:

what keeps this jack from backing down when weight is applied?

asked by: Dwayne O

0

Expert Reply:

The friction in the threads of the screw on the Lippert Scissor Stabilizer Jacks with Handle # LC285344 keep it from allowing itself to unscrew and lower itself. When the weight of the trailer pushes horizontally on the threads of the jack it does not allow it unscrew itself.

expert reply by: Jameson C

0

Answer 1

The only difference between the #RVLG-8HDL and the #RVLG-8000 is that the #RVLG-8HDL includes the manual crank handle, while the #RVLG-8000 doesn't. The dimensions for both are the same. • Retracted Height of 32-3/4 inches • Extended Height of…

view full answer...

Answer 2

The first thing you want to do before you find a replacement is to check the rating on your current landing gear. You want the new landing gear to be rated for at least the same amount. You will also need to measure the weld stops to make sure they…

view full answer...

Answer 3

The gearbox #RVLG-RDBOX for the Landing Gear Set w/ Handle #RVLG-8HDL can be mounted in the horizontal or vertical position. I went out to the warehouse and tested both the gearbox and lead leg together and the pins that hold the gearbox in place…

view full answer...

Answer 4

The only difference between the Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear #RVLG-8HDL that you mentioned, and the Landing Gear Set #RVLG-8000 is that #RVLG-8HDL comes with the handle, whereas if you were to go with…

view full answer...

Answer 5

The difference between the prices of the JR Products Automatic Changeover LP Gas Regulators and Camco Automatic Changeover 2-Stage Propane Regulators are in the BTU per hour, which as you correctly noted, is important information. The JR Products…

view full answer...

Answer 6

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Answer 7

Hey Bryan, We do not carry the garden hose adapter for that unit. We do have a replacement hose with hand sprayer #PF267003 that would work with that units quick-connect shower port. Are you specifically looking for one or the other? Or just seeing…

view full answer...

Answer 8

We have scissor jacks that will work for you, just keep in mind that scissor jacks are only designed to stabilize a portion of your weight as opposed to the full 15,000 lbs. The scissor jacks with the largest capacity are the Ultra-Fab Ultra Scissor…

view full answer...

Answer 9

I can certainly point you in the right direction. The big factor here is how much clearance you have in your wheel well. A typical 225/75R15 is 8.9" wide and 28.4" across when fully inflated. If we go up to a 16" tire like a…

view full answer...

Answer 10

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 11

Trailer manufacturers do not typically keep record of smaller parts such as the scissor jacks that would have come with your 2016 Keystone Springdale Summerland Mini 17. With that being said, just about any properly rated scissor jack will work great…

view full answer...

Answer 12

Hey Robbie, the Furrion Chill Cube RV Air Conditioner w Air Distribution Box #FR39TD that you referenced comes with everything needed to replace your Coleman Mach setup. How did you like your Coleman Mach Air?

view full answer...

Why Doesn't the Lippert Scissor Stabilizer Jacks # LC285344 Lower Itself From Weight of Trailer

Product Page this Question was Asked From

Continue Researching