Replacement Air Compressor for Roadmaster BrakeMaster # RM-9060

Question

Question:

Can I buy just the air pump and tank assembly, everything else has already been replaced. Thank you.

asked by: Jerry R

0

Expert Reply:

The Replacement Air Compressor # RM-8315 is the correct part for the Roadmaster BrakeMaster # RM-9060.

expert reply by: Charles S

0

Answer 1

I pulled one of the Roadmaster BrakeMaster systems, part #RM-9060-900002 from our warehouse and took some measurements you requested. The air compressor housing measures 10 inches wide at the front, 8 inches deep, 10-3/4 inches tall and the width…

view full answer...

Answer 2

If your motorhome brake line has metric fittings, it will be necessary to use a metric-to-standard T-fitting to attach the proportioning valve. This fitting is not supplied in the RoadMaster BrakeMaster Second RV Kit for Hydraulic Brakes #RM-98300.…

view full answer...

Answer 3

If by pressure switch you mean just the break away switch for your Roadmaster BakeMaster 9000 then you can use part #RM-650898. For a complete BrakeAway Kit including the switch and air cylinder use part #RM-8600. If you refer to the Pressure Reducer…

view full answer...

Answer 4

What you described is actually the part #RM-8315 that is a component of the #RM-9060 and #RM-9060-900002. It is the air tank/air compressor assembly.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Thanks for the information Kevin! To flat tow your 2025 Ford Bronco with a standard bumper and LED lights, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect item #e84ZR Base…

view full answer...

Replacement Air Compressor for Roadmaster BrakeMaster # RM-9060

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching