Bayonet Fitting Cap Recommendation for 3 inch RV Sewer Pipe

Question

Question:

Hello, is this a bayonet tab style cap? Like this on at the attached photo? Regards

asked by: Josef

0

Expert Reply:

What you are looking for is the part # T1020-3VP which uses the 3 inch bayonet style fitting for a cap. The part # A0120SVP is for a smaller pipe diameter.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Valterra Water Inlet Cap and Strap for RVs - White - Gravity Fill #A0120SVP has an inner diameter between tabs of 1.5 inches. and inside diameter without tabs of 1.64 inches. The outer diameter is 1.96 inches. I've attached a photo to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

Yes, there is Joe! We've got two options for a slide topper that fits a 82-1/2" slide out. They are the Solera RV Slide-Out Awning item #LCV000165062 in black or white item #LCV000163287. Please note you'll want to make sure you have…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Bayonet Fitting Cap Recommendation for 3 inch RV Sewer Pipe

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching