Parts Needed to Attach SnowBear Snow Plow to 2013 Ford F-150

Question

Question:

i have a 2013 ford f-150 v6 eco boast and a snow bear plow that was on a 2003 chevy silverado i would like to put the plow on the ford so what do i need to put it on the ford

asked by: Darcy

0

Expert Reply:

If the Snowbear plow attaches to the vehicle with brackets and not a front hitch the kit you need is the part # SB397-105.

If instead you need a front hitch you would want the part # C31068.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 5

To install the Curt Hitch part #C31068 on your 2014 Ford F-150 with Ecoboost you will need to remove the air dam and then trim a small section of the lower fascia. See photo.

view full answer...

Answer 6

Hey Parker, Yep, it sure will; the correct front hitch that does fit your 2014 Ford F-150 Lariat EcoBoost is the following from Curt: - Curt Front Mount Trailer Hitch Receiver #C31068 I went ahead and verified this with Curt for you.

view full answer...

Answer 7

Hey Ted, thanks for reaching out! The (discontinued) Draw-Tite 65061 hitch will fit exactly the same as the Curt #C31068 front hitch on your 2009 Ford F-150. The only difference being that the Draw-Tite sticks out further, as you mentioned. Some…

view full answer...

Answer 8

I recommend the EcoHitch Hidden Front Mount Trailer Hitch Receiver #EH37FR for your 2021 Ram 3500. This 2" receiver is rated for a vertical load up to 1000lbs, trailer weight of 3,500lbs, and a line pull of 10,000lbs. This receiver will include…

view full answer...

Answer 9

Hey John! The only option we have for a front hitch on your 2017 Ford Expedition is the Curt item #C31068 you were looking at. It does have a 500 lbs tongue weight capacity so I am going to have to recommend you follow it even though you're just…

view full answer...

Answer 10

By "snaking" I presume you are referring to trailer sway, with the car hauler's rear end moving side to side above the 45 mph speed you mentioned. Trailer sway like this usually has one cause: too low tongue weight (TW). Car hauler…

view full answer...

Answer 11

I attached a picture of the mounting holes for the Bulldog Heavy-Duty A-Frame Coupler, #BD44150WH301 that you referenced for you to check out so that you can compare them to the ones on your current coupler. Based on the picture you submitted this…

view full answer...

Parts Needed to Attach SnowBear Snow Plow to 2013 Ford F-150

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching