Does The Redline Wet Equalizer Bolt, # 126B2, Come In Different Lengths

Question

Question:

I need this type of wet bolt in two sizes 3 and 2.5. I need these lengths NOT including the head of the bolt or the threads. And, both size wet bolts need to be 9/16. Do you have two part # that fit this need?.

asked by: Brian M

0

Expert Reply:

I called the supplier (Redline) and they said the only wet bolt they offer in a 9/16 inch diameter is the Redline Wet Equalizer Bolt, # 126B2. The length of this bolt, not including the head of the bolt or the threads is 2-5/16 inches.

The only other wet bolt we offer is the Redline Wet Equalizer Bolt, # 126A1, which is a 3-1/2 inches length with a 3/4 inches diameter.

expert reply by: Jeff D

0

Answer 1

The length figure for the wet bolt part #126A1 is measured from the below the head to end of the threaded section. So that does not include the hex head. I'd recommend measuring the usable length you need from your bolt. Most likely this will…

view full answer...

Answer 2

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 5

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 11

Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…

view full answer...

Answer 12

Hey, Lance. The direction the springs are in doesn't matter. They can be to the front or to the rear of the axle and will perform the same either way. What kind of trailer are you working on?

view full answer...

Does The Redline Wet Equalizer Bolt, # 126B2, Come In Different Lengths

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching