Mounting Hole Dimensions for the Dutton Lainson Winch part # DL14627

Question

Question:

What are the measurements of the bolt pattern to mount this winche?

asked by: Brian B

0

Expert Reply:

I went out into our warehouse to grab a Dutton Lainson Winch part # DL14627 to measure the bolt hole dimensions for you.

I attached a picture that has all of them listed.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 2

Hi Nathan; the only hitch available for their 2023 Volvo V60 Cross Country is the Stealth Hitches #SH47FR which does require trimming. Is it a lease and they don't want to alter it or are they worried about how it might look? It will be…

view full answer...

Answer 3

I believe you are asking how to remove the shower door part #PF267001 from the shower box without damaging the frame of the shower box. There should be a pin with a spring on either side of the door. If you can compress those pins in the door, you…

view full answer...

Answer 4

Thanks for the picture! While we do not have an exact replacement for a Profile 2000 winch we do recommend the Dutton-Lainson Hand Winch item #DL14627 as a replacement. This winch has an 1,800 lbs capacity and will work great with the 20' x…

view full answer...

Answer 5

The only repair kit we have for your Profile 2000 hand winch is the Winch Ratchet Repair Kit by Dutton-Lainson item #DL70475. If this isn't what you are needing you will have to replace your winch. I recommend the Dutton-Lainson Hand Winch -…

view full answer...

Answer 6

Hey Mark, the Fulton winch part #F142306 that you referenced does not have a freewheel position. Instead we have the similar Jif marine winch part #315-W2000D that does. The middle position does allow it to free wheel but it does spin the handle as…

view full answer...

Answer 7

With boat winches you generally only need 50 percent of the boats weight as the winch's weight capacity. So for a 18,000 lb boat like you have you'd need a winch with at least a 9,000 lb capacity. For that we have the Fulton XLT Powered Winch…

view full answer...

Answer 8

I took a look at the A-60 Surge Brake Actuator like the Dexter #DX56FR, and to remove the front pin you'll need to remove the locking ring from the front rolling pin on the passenger side, and push it out from the passenger side to the driver…

view full answer...

Answer 9

Hey Tim. There are only two jacks that will fit your current mounting bracket and they are both Fulton F2 jacks rated at 1,600 lbs. I have listed them below: Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind item #F1413060334 Fulton F2…

view full answer...

Answer 10

If the gear is broken on your existing Shelby winch, I recommend simply replacing the entire unit, as Shelby is no longer in business and replacement parts are not readily available. To replace your Shelby 5408 model, I recommend the Dutton-Lainson…

view full answer...

Answer 11

The mounting plate on the Fulton Single Speed Trailer Winch #F142201 is 5-3/8" long and 3-9/16" wide. The total height of the unit is 6-1/8" tall. I've also linked our review video for this winch that gives the overall dimensions…

view full answer...

Answer 12

I went out to our warehouse to take some measurements of the mounting base on the Fulton Single Speed Trailer Winch #F142306. The plate itself measures 6 inches long and 4 inches wide. The mounting pattern features a few oblong holes that allows it…

view full answer...

Mounting Hole Dimensions for the Dutton Lainson Winch part # DL14627

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching