Bearing Buddy Grease Seal Recommendation for L44649

Question

Question:

What is the ID of the stainless steel ring, my spindle size is 1.5? Will this fit my spindle?

asked by: Roy G

0

Expert Reply:

The inner diameter of the steel ring of the # BB60008 is 1.25 inches as it is designed to be used with hubs that have an inner bearing number of # LM67048.

Since your inner bearing seems to have a 1.5 inch inner diameter most likely you have the L44649 bearing (you need to verify this), and the correct kit for you would be part # BB60005.

expert reply by: Jameson C

0

Answer 1

If you can send me the diameter of the spindle where the grease seal sits and the diameter of the hub where the seal is pressed onto I can verify if we have the correct seal. Currently I do see we carry 2 hubs which use the Inner Bearing #LM67048 and…

view full answer...

Answer 2

The inner diameter of the steel ring of the Spindle Grease Seal Set #BB60008 is 1.25 inches as it will have the same inner diameter as the inner bearing #LM67048 that is rides against like what you currently have. Since you have an inner bearing of…

view full answer...

Answer 3

We have the Spindle Grease Seal Set for LM67048 Inner Bearing and 2.328 Bearing Buddy #BB60008 that is the only seal that is a fit for your referenced measurements and bearings. I've attached a video to assist.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Bearing Buddy Grease Seal Recommendation for L44649

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching